TGM 5, TGM 5-Ex Transmitter for angular position Operating instruction 42/14(cid:1)34 EN Rev. 03 Important instructions! They must absolutely be read and obeyed! Proper and safe operation of the TGM5 (-Ex) transmitter presup- poses that it is correctly transported and stored, installed and commissioned by experts and carefully operated and maintained. Only those persons conversant with the installation and commis- sioning of similar equipmet and who possess the necessary qual- ifications may work on the apparatus. They must observe the contents of this Operating instruction and the relevant safety reg- ulations for installation and operation of electrical apparatus. This apparatus has been designed and tested in accordance with DIN VDE 411, Part 1 „Safety Requirements for Electronic Mea- suring Equipment“ and has been supplied in a safe condition. To retain the apparatus in safe condition, the safety instructions with the title „Caution“ in this Operating instruction must be observed. Failure to comply with these safety instruction can result in death, severe bodily injuries and considerable damage to the apparatus itself or to other equipment. Should the information given in the Operating instruction prove to be inadequate at any time please consult the Technical Branch Office, subsidiary, or representative of ABB in your area. The industrial standards and regulations (e.g. DIN, VDI, VDE) as well as the directives, specifications and requirements governing explosion protection (e.g. ElexV, EX-RL, VDE, DIN EN) referred to in this Operating instruction are applicable in Germany. When using this device outside the German Federal jurisdiction, the rel- evant specifications, standards and regulations applicable in the country where the device is used must be observed. 42/14-34 EN 3 View A Version with plug connection PG 13.5 od./or 82±0.1 A M 15 x 1.5 B x120°=360° 17C A ∅60D∅62f8∅102 3 15 32 M6 120° 15deep 101 124 76 (200) Z-149632 E Z-14963/1 Fig. 1 Dimensional drawing of TGM 5(-Ex) (all dimensions in mm) 6 42/14-34 EN A E 116 5.6 PG13.5od./or M18x1.5 B C ∅60 107 A D 56 13 ∅4x9 71+0.2119 20036 29 32 Z-14962/1 91010 1+240.2 Z-14962/2 Fig. 2 Dimensional drawing of TGM5 (-Ex) (a dimensions in mm) with foot mounting 42/14-34 EN 7 A 112.5 E PG13.5od./or M18x1.5 B C A ∅60∅110j6∅158 D 130±0.2 32 35 11.5 61.5 200 Z-14961/1 9.5 55° Z-14961/2 Fig. 3 Dimensional drawing of TGM 5 (-Ex) with flange mounting (dimensions in mm) 8 42/14-34 EN View A Version with plug connection TGM 5 friction bearing ball bearing A ∅ 19f8 ∅ 10f8 E E B 1 × 45° 0.5 × 45° C 3 ± 0.1 – D 3.5 ± 0.1 – Z-14961/3 Cable entry Plug connection Pg13.5 M 18 x 1.5 angled straight E 71.5 90.5 ≈ 143 ≈ 157 to Fig. 3 42/14-34 EN 9 1.4 Connection (See Fig. 4 and 5) 1 2 3 4 1 2 3 4 1 2 3 4 + + - R R R A A A - - + +1 - +2 - +3/~ -/~ Z-5054 Fig. 4 Connection diagrams a 2-wire circuits b 3-wire circuits c 4-wire circuits Standard 1 2 3 4 rt blswws 1 (rt) = red 7 6 2 (bl) = blue ge 3 (sw) = black 2 1 5 4 (ws) = white 3 4 Z-13890-1 Fig. 5 Han 7D connector 10 42/14-34 EN