SK-ACPE User/Installation Manual COPYRIGHT© 2013 SK-ACPE TABLE OF CONTENTS 1. INTRODUCTION ......................................................................................................1 Introduction to SK-ACPE Card ID Numbers and Facility Codes Setting the Facility Codes 2. INSTALLATION ........................................................................................................3 Physical Installation Wiring .....................................................................................................................4 Power and Batteries ...............................................................................................5 Readers Inputs Chassis Ground Outputs ...................................................................................................................6 LED Indicators Typical Door Installation Diagram/Cable Types .....................................................7 RS-232 Connections ................................................................................................8 Tamper Switch RS-485 Connections ..............................................................................................10 Ethernet Programming the SK-ACPE with SK-NET™ 3. FACTORY SETTINGS ...............................................................................................11 4. READERS AND CARDS ...........................................................................................12 Using Secura Key Readers and Cards Using Non-Secura Key Readers and Cards Ordering Additional Cards Setting Facility Codes APPENDIX A – Wiring and System Configurations ....................................................A-1 APPENDIX B – System Components and Specifications .............................................B-1 APPENDIX C – Connecting a Modem to SK-ACPE .......................................................C-1 APPENDIX D – Connecting an SK-ACPE to a Local Area Network .............................D-1 APPENDIX E – SK-ACPE Troubleshooting Guide ........................................................ E-1 APPENDIX F – Preventing Lightning Damage ............................................................F-1 APPENDIX G –What’s new, and what has not changed in the SK-ACPE? .................G-1 V110113 3322346 (7940) SK-ACPe InStAllAtIon & oPerAtIng MAnuAl INTRODUCTION The SK-ACPE Advanced Control Panel is a highly sophisticated, yet simple to use, two door access control unit with built-in Ethernet communications. The unit accepts readers of almost any technology, with a Wiegand output up to 40 bits, including Proximity, Touch Card, Wiegand, Magnetic Stripe, Bar Code, Optical, and Biometric. Each of the two passageways controlled by the unit is completely independent of the other and is configured, programmed and viewed separately. Up to 100 SK-ACPE Panels may be linked together on a twisted pair (plus signal ground) RS-485 bus. When used with SK-NET™ software, a highly featured, easy to use, distributed intelligence access control system can be created. Each of the two passageways controlled by the SK-ACPE has two programmable inputs which may be programmed by the user to function as a Door Monitor, Tamper Monitor, Remote Open, Remote Inactive, Bell, Arming Circuit, or User Defined Input. Each of the two passageways controlled by the SK-ACPE has two outputs. One output is the “Latch Relay,” which operates the door locking or operating device. The other “Auxiliary Output” is programmable by the user to activate under one of several possible alarm or special conditions. SK-ACPE will control access for up to 65,535 individuals in 15 weekly time schedules (Time Zones) independently for each of the two passageways. Time Zones include a holiday schedule that is followed when one of the 32 user programmable holidays occur. Any Access Card may be designated as a “Limited Use” card, and its use may be restricted to allow access for a given number of days or weeks or for a given number of times. The SK-ACPE may be programmed with a PC. Transaction information is stored by the unit and may be downloaded to a PC, or serial printer. Up to 10,000 transactions are stored. Since the SK-ACPE has nonvolatile memory, reprogramming after a power loss is unnecessary. CARD ID NUMBERS AND FACILITY CODES Access cards used with the SK-ACPE have two encoded numbers: the ID number which is different on each card, and the Facility Code, (also called a system or site code) which is normally the same for all cards at a given site. When a card is read, the system first verifies the Facility Code, then it checks the ID Number against its internal “card list” in memory to see if the card is void or valid. It also checks the Time Zone, the card’s Antipassback status, and the Limited Use count. 1 SK-ACPe InStAllAtIon & oPerAtIng MAnuAl SETTING THE FACILITY (SYSTEM) CODE IMPORTANT Before programming or using a new unit, the correct Facility Code must be set. When power is first applied, or when the reset button is pushed (see Figure 3) the LED on each of the two readers will flash red and green alternately. While the LED is flashing, present an Access Card with the proper facility code to one of the readers and remove it (note LED turns solid green for about 1 second and the beeper beeps to indicate that the card has been read). The SK-ACPE will “remember” the facility code and retain it until reprogrammed. It is not necessary to present the access card to the second reader since it is automatically set for both passageways. After setting the facility code, wait for the LED to stop flashing before attempting to use the reader. To change a facility code (or to set the facility code if the LED is not flashing red/green), momentarily depress the reset button. The LED indicator will flash red and green alternately. If the reset button is pushed, but no card is presented to the reader before the LED indicator times out, the facility code will be unchanged. In some cases it may be necessary for the unit to recognize more than one facility code. Typical instances are when it is necessary to read cards that work in two independent locations that already have different facility codes or when two different reader technologies are used in the same system, each of which has a different facility code. The SK-ACPE can be set to recognize up to sixteen different facility codes. To program multiple facility codes, follow the procedure above for programming a single facility code, but present a card with the second facility code (and additional facility codes if necessary) to the reader before the red/green LED indicator times out. Note that it is not generally recommended to combine sets of cards with different facility codes, because the unit cannot distinguish between access cards having different facility codes and the same ID number. It is also important to distinguish between ID numbers and the facility code when programming. See Figure 1 for examples of the numbering location. For example, if you have two sets of cards numbered 1-100, with facility codes 12345 and 23456, and you delete cards 1 - 10 from the reader’s internal “card list,” then cards 1 - 10 with either facility code will be denied entry at the reader. SO # FC ID 1234567 12345 N0: 1234567 figure 1 2 SK-ACPe InStAllAtIon & oPerAtIng MAnuAl INSTALLATION CAUTION SHOULD BE TAKEN NOT TO TOUCH CIRCUIT BOARD OR ELECTRONIC COMPONENTS PRIOR TO AND DURING INSTALLATION TO AVOID ELECTRO-STATIC DISCHARGE (ESD) DAMAGE. INSTALLING THE SK-ACPE 1. Select a location for the SK-ACPE unit that is secure and sheltered from weather and extreme humidity. Choose a location that facilitates access to power and is reasonably close to the doors that are to be controlled (no further than 500 feet). 2. Using the unit as a template, mark on the mounting surface the location of the four mounting holes. 3. Install appropriate mounting hardware (anchors, retainers, etc.) to the mounting surface if necessary. 4. Screw #6 or #8 mounting screws into the top 2 mounting holes of the mounting surface, leaving about 1/4” clearance. 5. Place panel top key-way mounting holes over installed mounting screws and slide panel down. 6. Tighten top mounting screws. 7. Install two bottom mounting screws (see figure 2). 8. Route cables into the enclosure through knockouts in sides or back of box, being careful not to nick or scrape insulation on any rough edges. figure 2 3 SK-ACPe InStAllAtIon & oPerAtIng MAnuAl WIRING The SK-ACPE unit is organized so that the wiring for door #1 is on the right side of the panel and the wiring for door #2 is on the left side of the panel (see figure 3). For ease of installation and servicing, plug-in terminal blocks are provided. 654321 RG1SDD4IEAARG TTDVE AAGD EL CNN10ED DLJE6D WOiFPi TMIOONDJAU1LL E2 1 JP1 J5GRRESEEDDI1GND4AA TTGVLLAADNEE 01CDDD 123456 9 JUMPER JP1: 1 87654 ICINCNNOOO 21MM J2 BRUETSTEOTN 2 & 31 WE &Ni F2Ai BEMLNOEADSBU LJL7EE S& J11 J1 CCOONNNMMOCC 23456 3 NC NO 7 2 NO IN 1 8 1 COM COM 9 NC IN 2 6 1 5 NO SK-ACPE NC 2 43 CNOCM J4 J3 CONMO 34 2 NO NC 5 1 COM J8 J7 COM 6 NC NO GNDRS-485-ARS-485-B POWER - POWER +TAMPERTXDRTSCTSRXDGND J10 RJ1J 145 321 87654321 ETHERNET D) CHASSIS GROUND TERMINAL TSOKR -SOA-TC4H8P5EERs GND (BLK) 14 VDC (RE TROS H-2O3S2T STSKAW-MTITPSCE-CHRP CONNECT TO or TO HOST 16.5-24 VAC (50-60 HZ) EARTH GROUND SUCH AS 16-24 VDC A 10’ COPPER GROUND STAKE (BEST) OR AC POWER GROUND TO EARTH USING A 10 or 12 AWG WIRE GROUND COIN CELL BATTERY INFORMATION MODEL: 3V CR 1225 ------------------------------ K CHANGING OR REMOVING CA THE BATTERY: B USING A SUITABLE TOOL, REMOVE THE BATTERY FROM THE HOLDER BY PUSHING THE COIN CELL BATTERY FROM THE BACK SIDE figure 3 4 SK-ACPe InStAllAtIon & oPerAtIng MAnuAl POWER & BATTERIES The SK-ACPE unit must be connected to a source of low voltage power. The SK-ACPE should NOT be connected to the same power supply that is providing power to an electric lock or strike. To power the SK-ACPE, you must use a power supply, which is properly rated for the panel, plus any connected equipment: SK-ACPE with RK-WM / RK-WS readers 24VDC, 500 mA or 16.5VAC 40VA transformer SK-ACPE with SK-WLSE-MOD 24VDC, 500 mA or 16.5VAC 40VA transformer Add RK-WL readers to either of the above 16.5VAC 40VA transformer The basic configuration can be powered by the SK-ACP-PS, which includes a 24VDC 1A supply and a 4AH backup battery, or by a 16.5VAC 40VA transformer (SK-XFRMR) Terminals 7 & 8 on plug “J7” must be connected to 16.5 to 24 volts, AC or DC. You may also connect the SK-ACPE to 12 VDC, but in this case you must connect your power supply to the red (+) and black (-) wire leads on the lower left corner of the panel instead of the “J7” plug. If you use 12 VDC you cannot install a standby battery in the SK-ACPE. When 16.5 – 24 volts is used to power the SK-ACPE, you may connect the red and black wires to a 12 volt standby battery. Polarity (+/-) must be observed. The, 10” X 11” SK-ACPE-LE can accommodate batteries up to 4.0 Amp-hours Do not energize the SK-ACPE until all other connections are made. READERS SK-ACPE is designed to accept any reader or keypad with a standard Wiegand interface. The reader for door #1 is connected to plug “J5”, the reader for door #2 is connected to plug “J6”. (See figure 3) SUGGESTED CABLE IS Alpha 1296C. The SK-ACPE will provide up to 400mA to power each reader. If the readers you use require more current, an external power supply must be used. INPUTS Each reader may be associated with up to two auxiliary inputs. Inputs might include remote switches, door contact sensors, vehicle presence detectors, etc. If you connect inputs to the SK-ACPE you must define those inputs using SK-NET™ software (see SK-NET™ manual). Note that input 1 (#7) and input 2 (#9) share a common terminal (#8) on plugs “J1” and “J2”. All inputs are configured as normally open circuits. However, in many cases a “Door Monitor” input should be a normally closed circuit. To convert any input defined as “Door Monitor” to normally closed, you must reconfigure the inputs as Normally Closed, using the SK-NET™ software (see SK-NET Manual.) For testing and troubleshooting purposes, LED indicators are located on the circuit board near the input terminals, just below the LED Indicator for the Latch Relay (Figure 4). The LED lights when the input is in the alarm (off-normal) state. CHASSIS GROUND The SK-ACPE has a chassis ground terminal at the bottom of the PCBA just to the left of J8. This terminal must be connected to a good, reliable Earth ground, to enable the on-board gas tube surge suppressors to work effectively. If this is not done, damage to the controller may result. A crimp- type wire lug is supplied with the unit. Secure the lug to the terminal using the provided screw. Crimp the ground wire to 10AWG stranded, insulated wire, and connect the wire to the closest Earth ground available, such as a 10-ft buried copper grounding stake, Building Electrical Ground, or a steel cold water pipe, which must be contiguous, with no PVC or ABS sections. 5 SK-ACPe InStAllAtIon & oPerAtIng MAnuAl OUTPUTS Each door controlled by the SK-ACPE has two double pole, double throw relays associated with it. The “latch relays” are located on “J1” and “J2”, terminals 1-6. The “auxiliary relays” are located on “J3” and “J4”. One pole of the latch relay is typically used to open or close a circuit to unlock a door or activate a gate operator. The other pole of the latch relay operates simultaneously and may be used to shunt an alarm contact, start a video recorder, etc. The auxiliary relay may operate according to a variety of user-defined conditions. These must be programmed using SK-NET™ software (see SK-NET™ manual). NOTE: Two MOVs (metal- oxide varistors) are provided with each SK-ACPE. These must be installed between the “Common” and either the “Normally Open” or the “Normally Closed” terminals where power to the electric lock or strike is being switched (See Figures 7 and 8). For testing and troubleshooting purposes, an LED indicator is located on the circuit board adjacent to each relay. The LED lights when the relay is activated. COMMUNICATIONS JUMPER The jumper on pins 2 and 3 of Jumper connector JP1 must be installed to enable RS-232 communications at Jack J11 and J7. If the SK-WLSE-MOD Wireless network module is installed at J12, this jumper must be moved to pins 1 and 2 of JP1 to enable RS-232 communications with the wireless module. LED INDICATORS The SK-ACPE features 12 LED indicators, which will assist the installer when connecting, testing and troubleshooting the readers, inputs and outputs, power and communications wiring. These indicators and their functions are described in Figure 4. WIRELESS LED Locations & Legend ADAPTER COMMS** CPU & POWER STATUS* LED 1: WIRELESS ADAPTER COMMS READER 2 READER 1 BLUE BLINK - SEARCHING SHORTED SHORTED SOLID BLUE - CONNECTED LED 2: CPU & POWER STATUS LATCH LATCH RELAY 1 GREEN BLINK - STATUS OK RELAY 2 ACTIVE ACTIVE AMBER BLINK - AC POWER FAIL INPUT 1-1 ACTIVE INPUT 2-1 RESET RED BLINK - BATTERY FAIL ACTIVE BUTTON INPUT 1-2 LED 3: READER 2 POWER SHORTED INPUT 2-2 ACTIVE ACTIVE LED 4: READER 1 POWER SHORTED LED5: LATCH RELAY 2 ACTIVE AUX REALUAXY 1 RELAY 2 ACTIVE LED 6: LATCH RELAY 1 ACTIVE ACTIVE LED 7: INPUT 2-2 ACTIVE LED 8: INPUT 2-1 ACTIVE LED 9: INPUT 1-1 ACTIVE LED 10: INPUT 1-2 ACTIVE LED 11: AUX RELAY 2 ACTIVE LED 12: AUX RELAY 1 ACTIVE **WIRELESS COMMS *CPU & POWER STATUS LED 13: RS-485 HOST COMMS RHSO-4S8T5 SBOLLUIDE BBLLUINEK - -C SOENANRNCEHCINTEGD AMRBEGEDRR B EBLELINNIN KBK L- -IB NAAKCT -TP AEOLRWLYE OFRAK FILAIL COMMS figure 4 6