MIC-ALM 8 Input Alarm Card Installation Manual Bosch Security Systems EN Installation and Operation Manual MIC-ALM 8-Input Alarm Card | Installation and Operation Manual AAAEN| 2 MIC-ALM Alarm Card 8 input alarm card for MIC-240PSU, MIC-115PSU, MIC-24PSU, MIC-12PSU Power Supply Units Installation and Operation Manual Chapters_______________________________________________ 1. Introduction 2. MIC-ALM Installation Instructions 3. MIC-ALM Washer Pump Installation Instructions 4. Technical Specifications Bosch Security Systems Issue 1 MIC-ALM 8-Input Alarm Card | Installation and Operation Manual AAAEN| 3 Introduction................................................................ 1-6 MIC-ALM 8 input Alarm Card ................................................................ 1-6 Versions................................................................................................. 1-7 Features................................................................................................. 1-7 Unpacking.............................................................................................. 1-8 Packaging Contents............................................................................... 1-8 MIC-ALM 8 input Alarm Card Functionality..……….. 2-8 MIC-ALM 8 Input Alarm Card Installation…………...…………………... 2-9 Alarm Connections………………………………………………………… 2-10 Configuring the Alarms through Camset………………………..………. 2-11 Loading Camset V.50…………………………………………………...… 2-11 Using the Setup Buttons…………………………………………..………. 2-12 Washer Pump Drive Function……………………….. 3-13 Washer Pump Drive Installation………………………………………….. 3-13 Technical Specifications............................................ 4-14 Technical Specifications…………………………………………………… 4-14 Bosch Security Systems Issue 1 MIC-ALM 8-Input Alarm Card | Installation and Operation Manual AAAEN| 4 Safety Precautions 1. Read all instructions prior to installation. 2. Keep this manual for future reference. The following symbols are used throughout this manual please pay careful 3. Heed all warnings. attention to their meaning. 4. Install according to manufacturer’s instructions. 5. Qualified persons only should install this product, if in doubt consult a qualified T h e l ig h t n i ng flash with an arrowhead symbol within a triangle installer. is intended to alert the user to the presence of non-insulated 6. Use correct electrostatic discharge handling procedures when handling printed “dangerous voltage” within the product’s enclosure that may circuit boards to avoid damage to electro-sensitive components. be of sufficient magnitude to constitute a risk of electric shock 7. Do not install near any strong heat sources such as furnaces. to persons. 8. Never push objects or pour liquids into the product enclosure as this can cause a fire or electrical shock hazard. 9. Only use electronic cleaning solvent in the unlikely event of the card requiring The exclamation point within a triangle is intended to alert the cleaning. user to the presence of important safety, operating and 10. Ensure that the product is correctly earthed. maintenance (servicing) instructions in the literature 11. Use only the power sources indicated in this user guide and ensure that the accompanying the appliance. current rating of the supply cable is adequate for the product. 12. Do not overload power supply sockets as this can be a fire or electrical shock hazard. Important Safety Instructions 13. In the event of failure do not attempt to service this product yourself, please contact Bosch Security Systems for assistance. 14. Only use approved attachments or accessories specified by the manufacturer. Any CAUTION: TO REDUCE THE RISK OF ELECTRICAL changes or modifications made to the equipment, not expressly approved in writing SHOCK, DISCONNECT POWER SUPPLY BEFORE from Bosch Security Systems, could prevent proper or safe operation of the OPENING THE POWER SUPPLY UNIT. product and will invalidate the warranty. POWER DISCONNECT: POWER SUPPLY UNITS HAVE 15. Please dispose of disused electrical & electronic equipment at an environmentally POWER SUPPLIED WHENEVER THE POWER CORD IS compatible recycling facility (contact Bosch Security Systems for further details). INSERTED INTO THE POWER SOURCE WARNING INS TA LLATIO N SHO ULD BE CARRIE D OUT BY QUA LIFIED PERSONNEL ONLY IN ACCORDANCE WITH THE APPLICABLE LOCAL CODES. BOSCH SECURITY SYSTEM ACCEPTS NO LIABILITY FOR ANY DAMAGES OR LOSSES CAUSED DUE TO INCORRECT OR IMPROPER INSTALLATION Bosch Security Systems Issue 1 MIC-ALM 8-Input Alarm Card | Installation and Operation Manual AAAEN| 5 This product complies with the following EC directives:- Glossary of Terms EMC Directive (89/336/EC as amended) PTZ - Pan/Tilt/Zoom Machinery Directive (98/37/EC) PSU - Power Supply Unit LV Directive (73/23/EC) IR - Infra Red RoHS (Restriction of Hazardous substances) 2002/95/EC WEEE (Waste Electrical & Electronic Equipment) 2002/96/EC This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local supplier for procedures for recycling this equipment. Reference Bosch Security Systems Issue 1 MIC-ALM 8-Input Alarm Card | Installation and Operation Manual AAAEN| 6 The MIC-ALM 8 Input Alarm Card enables MIC400 cameras to support up to 8 external alarms such as Passive IR sensors, tamper switches or other alarm triggers. The MIC-ALM is designed to plug directly into a non-IR version of MIC400 power supplies and provides volt free contact closures from external sensors, the card can be configured to accept normally closed contacts. In addition the MIC-ALM also provides for a washer pump driver function designed to enable MIC400 cameras to support third party washer kits to remotely clean the window of the MIC400 camera. The MIC-ALM provides a volt free contact rated at 240vAC up to 5 Amps to drive the third party washer pump; there are no fuses on the MIC-ALM card so fusing MUST be provided externally. CHAPTER 1 Introduction Versions Bosch Security Systems Issue 1 MIC-ALM 8-Input Alarm Card | Installation and Operation Manual AAAEN| 7 This card is only required for MIC400 Power Supply Units which do not support This manual covers the installation and operation of Bosch Security Systems integrated Alarm operations, these are the following MIC400 Power Supply Units:- MIC-ALM 8 input Alarm Card for the MIC400 range of PTZ Cameras. MIC-240PSU The MIC-ALM 8-Input Alarm Card is a Printed Circuit Board as shown below and MIC-12PSU plugs directly into Non IR Power Supply Units for the MIC400 PTZ Camera. MIC-24PSU MIC-115PSU The following MIC400 Power Supply Units include 4 –Alarm inputs and a Washer Pump Drive function as standard and are not covered by this manual, please refer to the MIC400 Power Supply Units Installation and Operation Manual instead :- MIC-IR-240PSU MIC-IR-12PSU MIC-IR-24PSU MIC-IR-115PSU Features The MIC-ALM 8 input Alarm Card has the following features: • 8 external alarm contacts. • 2 Volt Free alarm output relays • Volt Free Washer Pump Drive function • Easy installation into MIC1-400 non IR power supply units Unpacking Bosch Security Systems Issue 1 MIC-ALM 8-Input Alarm Card | Installation and Operation Manual AAAEN| 8 CHAPTER 2 MIC-ALM 8 Input Alarm Card Functionality • Check the exterior of the packaging for visible damage. If any items appear to have been damaged in transit please inform the shipping The MIC-ALM 8 Input Alarm Card provides 8 contacts which enable up to 8 company. external alarms to be connected to the MIC400 camera. The MIC-ALM Card also provides support for third party washer pumps and reservoirs and two (2) auxiliary • Unpack the unit carefully; although ruggedized this is electronic equipment output relays each rated at 240vAC up to 5 Amps. and should be handled with care. The washer function provides a volt free contact output rated at 240vAC at 5 • Do not use if any component appears to be damaged. Please contact Amps, wiring for this supply must be provided by the installer and it is Bosch Security Systems in the event of damaged goods. recommended that this supply is externally fused. A push to test button (SW1) is also provided to test the pump operation and expel air to prime the pump ready for • The shipping cartoon is the best way to transport the unit, save it & all operation. other packaging materials for future use. If the unit must be returned, use the original packing materials. The drive signal Washer Dr is a TTL signal generated by the MIC400 camera, this TTL signal causes the relay drive transistor to switch on thus energizing the relay and closing the relay contacts thereby activating the supply to the washer pump. CAUTION: Use proper ESD handling precautions to avoid electrostatic discharge. Wear a grounded wrist strap to prevent To facilitate the installation of third party Washer Pumps & Reservoirs a washer damage when handling electro-sensitive printed circuit boards. nozzle kit (MIC-WKT-IR kit) is available from Bosch Security Systems. Along with the MIC-WKT-IR kit, the MIC-ALM Card provides the required accessories to fit a third party washer pump and reservoir to a MIC400 camera. The MIC-WKT-IR kit consists of a 5mm twin jet washer nozzle and two (2) Packaging Contents brackets to allow mounting of the washer nozzle on to a MIC400 camera base or corner mount bracket (CMB) utilising the M8 x 20mm fixing bolts holding the Please check for the following contents camera base or between wall and corner mount brackets. • MIC-ALM 8 input Alarm Card Installation Manual (this Booklet) The washer pump, reservoir bottle & 5mm tubing are not supplied by Bosch • MIC-ALM 8 Input Alarm Card Security Systems and will need to be purchased separately to suit the particular installation. Bosch Security Systems Issue 1 MIC-ALM 8-Input Alarm Card | Installation and Operation Manual AAAEN| 9 MIC-ALM 8 Input Alarm Card Installation CAUTION: Electrical Danger: Ensure all power is disconnected before opening or working upon the MIC400 Power Supply Unit. Installation must be carried out by suitably qualified persons & all local safety regulations should be followed. 1. The power supply unit should be switched off and unplugged prior to carrying out any work. 2. Ensure that the four (4) card spacer supports fitted in the power supply are A. Right hand -Add on positioned in the left and right most mounting holes on the power supply card support spacers & printed circuit board, so that the MIC-ALM card is supported in each holes corner. 3. Should you need to reposition the card spacers first remove the four (4) screws holding the power supply PCB to the enclosure, turn the PCB over and remove the two (2) card spacer supports, these spacers should be re- fixed at the correct positions shown as A and B on Figure 1 below. B. Centre – Add on C. Connection card supphoorlet sspacers & Header CN1 4. Insert the MIC-ALM Card so that the connector labelled CN1 as shown on Figure 2 - MIC-ALM 8 Input Alarm Card PCB Layout Figure 2 below plugs into the CN1 header on the Power Supply labelled C on Figure 1. Then fix to the card spacer supports using M3x6 screws. 5. The MIC-ALM is now ready to accept third party external alarm and washer pump electrical connections. Please see Alarms Connections and Washer Pump Installation for more details. Figure 1:- MIC400 non-IR Power Supply PCB Layout Alarm Connections Bosch Security Systems Issue 1 MIC-ALM 8-Input Alarm Card | Installation and Operation Manual AAAEN| 10 CAUTION: Electrical Danger: Ensure all power is 3. For external outputs connect to the auxiliary contacts HD3 or HD5 disconnected before opening or working upon the MIC400 respectively as shown below:- Power Supply Unit. Installation must be carried out by suitably qualified persons & all local safety regulations should be followed. HD3 Alarm Output 1 To connect third party external alarm contacts please do the following:- 1 Relay contact 1 1. Open the PSU lid and locate the alarm header HD4 located at the lower left hand side of the MIC-ALM card. Feed the alarm wires through one 2 Relay contact 2 of the weather proof gland leaving sufficient slack to reach the terminal block HD4. 2. Wire the alarms into HD4 as shown in the table below:- HD5 Alarm Output 2 HD4 Alarm Inputs 1 Relay contact 1 1 Alarm 1 2 Relay contact 2 2 0v 3 Alarm 2 4 Alarm 3 4. The auxiliary contacts at HD3 and HD5 are rated to 240vAC at 5 Amps these are not fused on the card so must be externally fused by the 5 0v installer to suit the current draw to be expected by any third party equipment. 6 Alarm 4 5. The auxiliary outputs HD3 and HD5 are currently configured to close as follows:- 7 Alarm 5 8 0v HD3 any of alarms 1 to 4 active HD5 any of alarms 5 to 8 active 9 Alarm 6 6. Each alarm contact has an LED next to it which will not be lit whenever 10 Alarm 7 an alarm is received for that contact, in addition there are LED’s for the Washer Drive (HD1) and the two (2) Auxiliaries, HD3 and HD5 which 11 0v will be lit when the respective relay contact is closed. 12 Alarm 8 Configuring the Alarms through Camset Bosch Security Systems Issue 1
Description: