ISO/TS 16976-4:2019(E) Contents Page Foreword ........................................................................................................................................................................................................................................iv Introduction ..................................................................................................................................................................................................................................v 1 Scope .................................................................................................................................................................................................................................1 2 Normative references ......................................................................................................................................................................................1 3 Terms and definitions .....................................................................................................................................................................................1 4 Symbols and abbreviated terms ...........................................................................................................................................................2 5 Pressure and volume changes during breathing ................................................................................................................3 5.1 Pressure and volume changes in the absence of an RPD ....................................................................................3 5.2 The effect of RPD flow resistance on pressure and volume changes while using an RPD .....6 5.3 The effect of RPD with static pressure on pressure and volume changes while using an RPD .............................................................................................................................................................................................6 5.4 The effect of RPD flow resistance and static pressure on pressure and volume changes while using an RPD ........................................................................................................................................................7 5.5 Effects of high static pressure ....................................................................................................................................................7 6 Work of breathing (WOB)............................................................................................................................................................................8 6.1 Physiological work versus physical work ........................................................................................................................8 6.1.1 General......................................................................................................................................................................................8 6.1.2 Static work ............................................................................................................................................................................8 6.1.3 Elastic work ..........................................................................................................................................................................8 6.1.4 Positive and negative physical work ...............................................................................................................9 6.2 Calculations of inspiratory WOB .............................................................................................................................................9 6.3 Calculations of expiratory WOB ...............................................................................................................................................9 6.4 Calculations of total WOB ...........................................................................................................................................................10 6.4.1 Calculations of the wearer’s WOB while using an RPD ...............................................................10 6.4.2 Calculations of WOB for an RPD only ..........................................................................................................10 6.5 Breathing resistance .......................................................................................................................................................................11 6.6 Physiologically acceptable WOB ...........................................................................................................................................11 7 Other respiratory loads ..............................................................................................................................................................................13 7.1 Static load .................................................................................................................................................................................................13 7.2 Elastic loads ............................................................................................................................................................................................13 7.3 Other loads ..............................................................................................................................................................................................13 7.4 How respiratory loads add up ................................................................................................................................................13 8 Summary ....................................................................................................................................................................................................................14 Bibliography .............................................................................................................................................................................................................................15 © ISO 2019 – All rights reserved iii ISO/TS 16976-4:2019(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the developmentof the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/iso/foreword. html. This document was prepared by Technical Committee ISO/TC 94, Personal safety — Personal protective equipment, Subcommittee SC 15, Respiratory protective devices. This second edition cancels and replaces the first edition (ISO/TS 16976-4:2012), which has been technically revised. The main changes compared to the previous edition are as follows: a) adjustment of key-points in Figures 3, 4 and 7 to correspond with the 50 %-reference line; b) adjustment of keys in Figures 3, 4, 7 and 8; c) adjustment of Figures 3, 4 and 6; d) clarification on flow resistance and elastic load given in 7.4. A list of all parts in the ISO/TS 16976 series can be found on the ISO website. Any feedback or questions on this document should be directed to the user’s national standards body. A complete listing of these bodies can be found at www .iso .org/members .html. iv © ISO 2019 – All rights reserved ISO/TS 16976-4:2019(E) Introduction A respiratory protective device (RPD) is designed to offer protection from the inhalation of hazardous substances. However, this protection requires extra effort by the respiratory muscles as they need to generate higher pressures to overcome the associated respiratory loads imposed by the RPD. © ISO 2019 – All rights reserved v TECHNICAL SPECIFICATION ISO/TS 16976-4:2019(E) Respiratory protective devices — Human factors — Part 4: Work of breathing and breathing resistance: Physiologically based limits 1 Scope This document describes how to calculate the work performed by a person’s respiratory muscles with and without the external respiratory impediments that are imposed by RPD of all kinds, except diving equipment. This Document describes how much additional impediment people can tolerate and contains values that can be used to judge the acceptability of an RPD. NOTE These calculations are explained in some textbooks on respiratory physiology (in the absence of an RPD), but most omit them or are incomplete in their explanations. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 16972, Respiratory protective devices — Definitions of terms pictograms 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 16972 and the following apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: — ISO Online browsing platform: available at https:/ /www .iso .org/obp — IEC Electropedia: available at http: //www .electropedia .org/ 3.1 body temperature pressure saturated BTPS standard condition for the expression of ventilation parameters Note 1 to entry: Body temperature (37 °C), ambient pressure and water vapour pressure (6,27 kPa) in saturated air. 3.2 compliance change in volume of the human lung that results from a change in pressure Note 1 to entry: The compliance is measured in l/kPa. Note 2 to entry: This term is the typical term for the elastic behaviour of the lungs and chest. Compliance is the inverse of elastance. © ISO 2019 – All rights reserved 1 ISO/TS 16976-4:2019(E) 3.3 elastance change in pressure that results from a given volume change of the human lung Note 1 to entry: The elastance is measured in kPa/l. Note 2 to entry: This term is the typical term for the elastic behaviour of an RPD. Elastance is the inverse of compliance. 3.4 relaxation volume lung volume when respiratory muscles are relaxed, i.e. the volume at the beginning of an inspiration, also known as functional residual capacity (FRC) and expiratory reserve volume (ERV) 3.5 tidal volume V T volume of a breath Note 1 to entry: The tidal volume is measured in litres BTPS. 3.6 vital capacity VC volume of the largest breath a person can take, i.e. the volume difference between a maximum inspiration and a maximum expiration Note 1 to entry: The vital capacity is measured in litres BTPS. 3.7 work of breathing WOB work required for an entire breathing cycle Note 1 to entry: The work in breathing is measured in Joules. 3.8 work of breathing per tidal volume WOB/V T normalized WOB (equivalent to volume-averaged pressure) Note 1 to entry: The work in breathing per tidal volume is measured in Joules per litre = kPa. 4 Symbols and abbreviated terms BTPS body temperature pressure saturated ERV expiratory reserve volume FRC functional residual capacity RPD respiratory protective device VC vital capacity WOB work of breathing 2 © ISO 2019 – All rights reserved ISO/TS 16976-4:2019(E) p pressure required to overcome the elastance el p pressure required to overcome the flow resistance of the airways aw p pressure required to overcome the inspiratory flow resistance of the RPD i,ext 5 Pressure and volume changes during breathing 5.1 Pressure and volume changes in the absence of an RPD During an inspiration the inspiratory muscles contract which makes the chest expand and the diaphragm flatten. This action causes the lungs to expand to a larger volume. Even in the absence of flow resistance, it takes a certain pressure to expand the chest and lungs. The term used in respiratory physiology for this elastic behaviour is compliance. The term compliance is also used in laws and regulations; to avoid confusion with this use of the word, the remainder of this document will use the term elastance instead. See Note 2 to entry of 3.3, "elastance is the inverse of compliance". Elastance describes how much an elastic material changes when a force or a pressure is applied. Figure 1 shows the lungs (item 1) inside the chest wall (item 2) and diaphragm (item 3). The lungs are connected to the airway (item 4). The elastance of the lungs tries to act to shrink them (shown by the arrows), similarly to a stretched balloon trying to shrink in volume. The elastance of the chest acts by trying to expand it. Thus, in the absence of muscle effort, the forces on the chest and lungs oppose each other and will, at some volume, be equal and opposite and come to a position of rest. The lung volume at which this happens is referred to as the relaxation volume. During an inhalation the chest wall expands and the diaphragm (item 3) moves downwards. Key 1 lungs 2 chest wall 3 diaphragm 4 airway Figure 1 — Schematic cross-section of a person’s chest and lungs Figure 2 illustrates/defines changes in breathing. An inspiration is shown to start at point A and the lung volume increases until it reaches its end, point B, where the following expiration starts. The volume difference between points A and B is the size of the breath, referred to as the tidal volume. A maximum inspiration is shown at point C and a maximum expiration at point D. The volume difference between these two points is the maximum volume change achievable and is referred to as the vital capacity, VC. The range of VC varies from 3 l to 6 l and depends on a person’s age, height and gender. © ISO 2019 – All rights reserved 3 ISO/TS 16976-4:2019(E) Even with a maximum expiratory effort some volume remains in the lungs. Had the lungs been able to be emptied completely the volume illustrated by line E would have been reached. Point A is the point where the respiratory muscles are relaxed and that volume is referred to as "relaxation volume". Another term used for this point is "expiratory reserve volume", ERV, which can be calculated as the difference between points A and D. A third term used is "functional residual capacity", FRC, which is the volume difference between points A and E. Key X time Y lung volume A start of an inspiration B end of an inspiration and start of the following expiration C maximum inspiration D maximum expiration E lungs and chest completely empty Figure 2 — Definitions of volume changes In order to inhale, effort is required to overcome the combined elastance of the chest and lungs, as well as the flow resistance in the airways. Figure 3 illustrates the pressure generated and the resulting volume changes. 4 © ISO 2019 – All rights reserved