इंटरनेट मानक Disclosure to Promote the Right To Information Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information under the control of public authorities, in order to promote transparency and accountability in the working of every public authority, and whereas the attached publication of the Bureau of Indian Standards is of particular interest to the public, particularly disadvantaged communities and those engaged in the pursuit of education and knowledge, the attached public safety standard is made available to promote the timely dissemination of this information in an accurate manner to the public. “जान1 का अ+धकार, जी1 का अ+धकार” “प0रा1 को छोड न’ 5 तरफ” Mazdoor Kisan Shakti Sangathan Jawaharlal Nehru “The Right to Information, The Right to Live” “Step Out From the Old to the New” IS 15942 (2011): Technical drawings – symbolic presentation and indication of adhesive, fold and pressed joints [PGD 24: Drawings] “!ान $ एक न’ भारत का +नम-ण” Satyanarayan Gangaram Pitroda ““IInnvveenntt aa NNeeww IInnddiiaa UUssiinngg KKnnoowwlleeddggee”” “!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता हहहहै””ै” Bhartṛhari—Nītiśatakam “Knowledge is such a treasure which cannot be stolen” IS 15942 : 2011 ISO 15785 : 2002 Hkkjrh; ekud rduhdh MªkbZxsa vklatd] QksYM ,oa izSLM tksM+ksa — ds flEcksfyd izLrqrhdj.k ,oa ladsru Indian Standard TECHNICAL DRAWINGS — SYMBOLIC PRESENTATION AND INDICATION OF ADHESIVE, FOLD AND PRESSED JOINTS ICS 01.100.20 © BIS 2011 BU R E AU O F I N D I A N S TA N DA R D S MANAK BHAVAN, 9 B AHADUR SHAH ZAFAR MARG NEW DELHI 110002 August 2011 Price Group 4 Drawings Sectional Committee, PGD 24 NATIONAL FOREWORD This Indian Standard which is identical with ISO 15785 : 2002 ‘Technical drawings — Symbolic presentation and indication of adhesive, fold and pressed joints’ issued by the International Organization for Standardization (ISO) was adopted by the Bureau of Indian Standards on the recommendation of the Drawings Sectional Committee and approval of the Production and General Engineering Division Council. The text of ISO Standard has been approved as suitable for publication as an Indian Standard without deviations. Certain terminology and conventions are, however, not identical to those used in Indian Standards. Attention is particularly drawn to the following: a) Wherever the words ‘International Standard’ appear referring to this standard, they should be read as ‘Indian Standard’. b) Comma (,) has been used as a decimal marker while in Indian Standards, the current practice is to use a point (.) as the decimal marker. In this adopted standard, reference appears to certain International Standards for which Indian Standards also exist. The corresponding Indian Standards which are to be substituted in their respective places are listed below along with their degree of equivalence for the editions indicated: International Standard Corresponding Indian Standard Degree of Equivalence ISO 128-20 : 1996 Technical drawings IS 10714 (Part 20) : 2001 Technical Identical — General principles of presentation drawings — General principles of — Part 20: Basic conventions for lines presentation: Part 20 Basic conventions for lines ISO 128-22 : 1999 Technical drawings IS 10714 (Part 22) : 2006 Technical do — General principles of presentation drawings — General principles of — Part 22: Basic conventions and presentation: Part 22 Basic conventions applications for leader lines and and applications for leader lines and reference lines reference lines ISO 3098-0 : 1997 Technical product IS 9609 (Part 0) : 2001 Technical do documentation — Lettering — Part 0: product documentation — Lettering: General requirements Part 0 General requirements The technical committee has reviewed the provisions of the following International Standards referred in this adopted standard and has decided that they are acceptable for use in conjunction with this standard: International Standard Title ISO 128-24 : 1999 Technical drawings — General principles of presentation — Part 24: Lines on mechanical engineering drawings ISO 129-1 : 2004 Technical drawings — Indication of dimensions and tolerances — Part 1: General principles ISO 2553 : 1992 Welded, brazed and soldered joints — Symbolic representation on drawings ISO 17659 : 2002 Welding — Multilingual terms for welded joins with illustrations (Continued on third cover) IS 15942 : 2011 ISO 15785 : 2002 Indian Standard TECHNICAL DRAWINGS — SYMBOLIC PRESENTATION AND INDICATION OF ADHESIVE, FOLD AND PRESSED JOINTS 1 Scope This International Standard establishes rules for the symbolic presentation and indication of adhesive, fold and pressed joints in technical drawings. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 128-20, Technical drawings — General principles of presentation — Part 20: Basic conventions for lines ISO 128-22, Technical drawings — General principles of presentation — Part 22: Basic conventions and applications for leader lines and reference lines ISO 128-24:1999, Technical drawings — General principles of presentation — Part 24: Lines on mechanical engineering drawings ISO 129-1:—1), Technical drawings — Indication of dimensions and tolerances — Part 1: General principles ISO 2553, Welded, brazed and soldered joints — Symbolic representation on drawings ISO 3098-0:1997, Technical product documentation — Lettering — Part 0: General requirements ISO 17659:2002, Welding — Multilingual terms for welded joints with illustrations 3 Terms and definitions For the purposes of this International Standard, the terms and definitions given in ISO 128-22 and the following apply. 3.1 joint junction of workpieces or edges of workpieces that are to be joined or have been joined [ISO 17659:2002, definition 3.1] 1) To be published. (Revision of ISO 129:1985) 1 IS 15942 : 2011 ISO 15785 : 2002 3.1.1 adhesive joint joint of two or more parts of similar or different materials made using adhesives 3.1.2 fold joint joint of two edges of surfaces of similar or different materials made by catching and coupling 3.1.3 pressed joint joint of two or more parts of sheet materials made by simultaneous deformation from two sides by means of (cylindrical, rectangular etc.) tools 4 Graphical symbols 4.1 General The joints specified in this International Standard are identified by the symbols shown in Figures 1 to 4. The manner of presentation and the dimensions of these symbols are given in Annex A. NOTE The symbols shown in Figures 1 to 3 are identical to those given in ISO 2553 for joints of identical configuration. 4.2 Adhesive joints Adhesive joints shall be identified by the symbols shown in Figures 1 and 2. A surface joint shall be identified by the symbol shown in Figure 1. Figure 1 — Symbol for surface joint An inclined joint shall be identified by the symbol shown in Figure 2. Figure 2 — Symbol for inclined joint 4.3 Fold joint A fold joint shall be identified by the symbol shown in Figure 3. 2 IS 15942 : 2011 ISO 15785 : 2002 Figure 3 — Symbol for fold joint 4.4 Pressed joint A pressed joint shall be identified by the symbol shown in Figure 4. Figure 4 — Symbol for pressed joint 5 Indication of joints in drawings The symbols shall be drawn using a continuous wide line in accordance with ISO 128-24 (see Figure 5 for an example), supplemented by the applicable information in accordance with ISO 2553. The distance between the graphical symbol and the reference line shall be at least 2d (for d, see Annex A). The leader line and reference line shall be drawn using a continuous narrow line in accordance with ISO 128-22. The leader line shall end in an arrow (see Figure 5) and the reference line may begin with a fork (see Figure 6), where additional requirements may be indicated (see Figure 7). Figure 5 — Symbol with reference line and leader line Figure 6 — Reference line with fork Figure 7 — Additional information with reference line 3 IS 15942 : 2011 ISO 15785 : 2002 In addition to the symbol, the following may be indicated with the reference line, as necessary: a) the dimensions of the cross-section of the joint (width and height, punch diameter, depth of punching etc.), placed at left of symbol; b) other characteristics, for example, designations of the material, placed at right of symbol; c) additional requirements for the joint, placed in the fork (see Figure 7). The dimensions that locate the joint shall be indicated in accordance with ISO 129-1. 6 Basic conventions for symbolic presentation and indication of joints 6.1 Adhesive joints Adhesive joints shall be shown without an indication of the adhesive, as shown in Figures 8 and 9. Figure 8 — Indication of surface joint Figure 9 — Indication of inclined joint To indicate a continuous adhesive joint formed around the periphery of a part, a circle shall be added at the intersection between the leader and reference lines in accordance with ISO 128-22 (see Figure 10). Figure 10 — Indication of joint around periphery 4 IS 15942 : 2011 ISO 15785 : 2002 An adhesive joint limited to an area shall be indicated using a type 05.1.8 long-dashed double-dotted narrow line in accordance with ISO 128-24:1999 (see Figure 11). Figure 11 — Indication of limited area 6.2 Fold joints Fold joints shall be presented in accordance with the general principles given in ISO 128-20, ISO 128-22 and ISO 128-24. 6.3 Pressed joints If a joint is made by mechanical pressing in more than one place, the dimensions specifying the locations of the pressings shall be shown on the presentation of the parts being jointed (see Figure 12). Figure 12 — Indication of pressed joint 7 Designation examples Examples of designations are given in Table 1. 5