Information sheet (Supplement to Technical Regulations, chapter 4.4.3) Use of glass and acrylic glass in stand construction and design inside trade fair halls Page 1 Use of glass and acrylic glass in stand construction and design inside trade fair halls CONTENTS Page 1 SCOPE OF APPLICABILITY ...................................................................................................... 2 2 DEFINITIONS AND EXPLANATIONS ........................................................................................ 2 2.1 Types of supports ...................................................................................................................... 2 2.2 Types of glass and acrylic glass .............................................................................................. 2 2.3 Design calculation standards ................................................................................................... 3 2.4 Material properties of glass products ...................................................................................... 4 3 STAND DESIGN, CONSTRUCTION AND LOADS ..................................................................... 4 3.1 Vertical glazing not intended to prevent falling ...................................................................... 4 3.1.1 Vertical glazing of a height h 4 metres above hall floor level .................................................... 4 3.1.2 Vertical glazing of height h > 4 metres above hall floor level ...................................................... 4 3.2 Vertical glazing intended to prevent falls ................................................................................ 5 3.2.1 Category A – vertical glass wall ................................................................................................... 5 3.2.2 Category B – clamped glass balustrade with continuous handrail ............................................... 5 3.2.3 Category C – Railing and balustrade infills and glass walls with load-distributing cross-bar fitted in front of it ................................................................................................................................... 6 3.3 Horizontal glazing ...................................................................................................................... 6 3.3.1 Overhead glazing ........................................................................................................................ 6 3.3.2 Glazing designed to support human loads ................................................................................... 7 4 APPROVAL PROCEDURES ...................................................................................................... 8 4.1 Basics ......................................................................................................................................... 8 4.2 Installation approval for a specific case .................................................................................. 8 5 NOTES ON DESIGN AND DESIGN CALCULATIONS ............................................................. 10 6 EXAMPLES OF STRUCTURES (BARRIERS) DESIGNED TO PREVENT FALLS. ................. 10 6.1 Category B ............................................................................................................................... 10 6.2 Category C1 ............................................................................................................................. 11 6.2.1 Railing infills secured vertically on 2 sides ................................................................................. 11 6.2.2 Railing infills secured horizontally on 2 edges .......................................................................... 11 6.2.3 Railing infills secured on 4 sides ................................................................................................ 11 6.2.4 Glazing secured at individual points by means of drilled anchorage points (design specifications in accordance with TRAV and/or DIN 18008-4) ......................................................................... 12 6.2.5 Point mounting with lateral clamps and anti-slip grips ............................................................... 13 6.2.6 Point mounting with clamps at top and bottom .......................................................................... 13 6.3 Balustrade with horizontal bars (protection against falling is provided solely by sufficiently strong handrails and knee-height bars) ............................................................. 13 7 CONSTRUCTION ENGINEERING REGULATIONS, GENERALLY ACCEPTED RULES OF ENGINEERING AND REFERENCES ....................................................................................... 14 8 ABBREVIATIONS ..................................................................................................................... 15 9 KEYWORD INDEX .................................................................................................................. 156 Information sheet (Supplement to Technical Regulations, chapter 4.4.3) Use of glass and acrylic glass in stand construction and design inside trade fair halls Page 2 1 SCOPE OF APPLICABILITY This information sheet discusses the regulations concerning the use of glass and acrylic glass in stand construction and design inside trade fair halls. It does not apply to stand construction and design outside trade fair halls. Designing, dimension calculations and assembly of glass components for use inside trade fair halls require that the design, planning and assembly personnel involved is adequately qualified for glass construction projects. Glass structures which have received general construction approval (including European Technical Approval ETA) may be used in all cases in trade fair halls in accordance with the wording of the approval. This information sheet does not impose restrictions on the use of such structures. 2 DEFINITIONS AND EXPLANATIONS 2.1 Types of supports - Glazing secured by linear supports: secured by linear supports on at least two opposite edges over the full length of each edge of the glass plate. - Glazing secured at individual points: glazing anchored through drilled holes or by a clamping system. 2.2 Types of glass and acrylic glass Types of glass granted statutory construction approval in Building Regulation List A: - Float glass (polished plate glass – PPG) as specified in DIN EN 572-2: Also called flat or plate glass. It is characterised by relatively low ultimate flexural strength, and when destroyed, it fragments into large sharp-edged shards. Its use as single sheet glazing in trade fair construction is prohibited. If used in LSG, it is permitted in trade-fair construction. - Tempered safety glass (TSG) as specified in DIN 12150-1: TSG is a fully thermically pre-stressed type of glass. It has internal residual stress characteristics: core tensile stress and surface compression stress. It has high ultimate flexural strength and when broken, it shatters into crumb-like fragments. Where TSG is referred to in this information sheet, TSG made of float glass is always meant. - Laminated safety glass (LSG): LSG consists of at least two sheets of PPG, TSG or HSG glass. The individual thicknesses of these are not permitted to differ from each other by a factor of more than 1.5. The sheets of glass are laminated together by intermediate film layers (PVB or SGP films). If a sheet is broken, then the film prevents the fragments from being scattered, thus providing residual load-bearing capacities and reducing the risk of injury from cuts. - Heat-strengthened glass (HSG) as specified in DIN EN 1863-1 or with other general approvals by building authorities (German:allgemeine bauaufsichtliche Zulassung – abZ): HSG is a type of glass that is only partially thermically pre-stressed. Its ultimate flexural strength is lower than that of TSG (tempered safety glass). When broken, HSG fragments into shards which are larger than those of broken TSG. Therefore LSG sheets made of HSG have higher residual load-bearing capacities than LSG sheets made of TSG. HSG laminated with PVB film is included in Building Regulation List A. A general construction approval by building authorities (German allgemeine bauaufsichtliche Zulassung – abZ) for the SGP film is required for HSG laminated with SGP. Types of glass for which no statutory construction approval has been granted: - Acrylic glass: Acrylic glass is a transparent thermoplastic product marketed under the brand names Plexiglas® and Perspex®, for example. At present no recognised technical regulations are available for the use of acrylic glass. - Polycarbonate products: e.g. Makrolon Acrylic glass and polycarbonate may only be used for non-load-bearing, decorative infill components. Information sheet (Supplement to Technical Regulations, chapter 4.4.3) Use of glass and acrylic glass in stand construction and design inside trade fair halls Page 3 2.3 Design calculation standards The static strength proof calculations for glass components can be carried out in accordance with the following design calculation concepts and structural design standards: Design concept A: comprehensive safety concept B: load factor concept Proof concept σ < allow. σ σ*γ < f*k*k / γ κ f k c mod M Determination of action effects and stresses at SLS (GZG)*) at ULS (GZT)*) Deformation checks at SLS (GZG) at SLS (GZG) Designation of forces /stresses in the SLS (GZG) after the number or serviceability limit state SLS (forces due to index k after formula symbol no designation characteristic loads, without γ) f SLS (GZG) e. g. supporting force = 12 kN (SLS) or F = 12 kN k Designation of forces /stresses in the ULS (GZT) after the number or ultimate limit state ULS (forces due to index d after formula symbol characteristic loads, multiplied by γ) f e. g. supporting force = 16 kN (ULS) or F = 16 kN d Designation of the allowable material stress allow. σ or allowable σ (zul. σ or zulässig σ) Designation of the limit stress f k Dimension calculation rules, dimension DIN 18008-1 [12] calculation standards TRLV [5] DIN 18008-2 [13] TRAV [6] DIN 18008-3 [14] TRPV [17] DIN 18008-4 [15] DIN 18008-5 [16] Standards applying to loads and actions this information sheet and this information sheet and DIN EN 1991-1-1 DIN EN 1991-1-1 DIN EN 1991-1-1/NA: (2010-12) DIN EN 1991-1-1/NA: (2010-12) Normal load factors γfor permanent loads f 1.35 (e. g. dead loads) Normal load factors for variable loads and actions (e. g. dynamic pressure, imposed 1.5 loads, cross-bar pressures) Duration of loads typically encountered at Own weight: permanent trade fairs for k , taken from DIN 18008-1, (k = 0.25) mod mod Table 6. Working loads:medium (k = 0,4) mod Horizontal substitute load: short (k = 0,7) mod Cross-bar pressure: short (k = 0,7) mod *) German designations and abbreviations Grenzzustand der Gebrauchstauglichkeit - GZG and Grenzzustand der Tragfähigkeit - GZT [as listed in chapter 8] for the respective limit states. For static load calculations, either concept A, comprehensive safety, or concept B, load factors, shall be used as a basis. The two concepts must not be mixed (used together). After the design dimension calculation concept A or B has been chosen, all design requirement specifications (e. g. flexing limits, glass clamping depth etc.) given in the set of standards chosen for the design concept are to be applied. The verbal description and the symbols and abbreviations used in equations must make it absolutely clear which concept is being applied. Supporting forces transmitted by glass components must always be stated for the SLS (GZG) and the ULS (GZT) so that the loads of the connected force-transmitting components of concrete, steel or wood can be calculated using the load-factor concept without transmission errors. Information sheet (Supplement to Technical Regulations, chapter 4.4.3) Use of glass and acrylic glass in stand construction and design inside trade fair halls Page 4 2.4 Material properties of glass products Glass products have a bulk density of 25 kN/m³, a thermal expansion coefficient of 8.4·10-6/K and their Young´s modulus is 70,000 N/mm². For structural design calculations, the bending stresses listed in Table 1 are allowed (concept A) or the design calculation values of the resistance Rd listed in Table 2 must be observed (concept B). Table 1: Allowable bending stresses for various glass sorts, in N/mm² (for static proof calculations according to the allowable stress concept) Enamelled glass Heat- LSG made Float glass Toughened / (printed glass) strengthen with float (polished Wire glass (only for fully-tempered ed glass glass plate glass existing components) glass (TSG) TSG HSG HSG (PPG) PPG) Overhead glazing 50 30 18 29 15 12 8 Vertical glazing 50 30 18 29 22,5 18 10 Table 2: Normal material properties for design calculation concept B, application of load factors Polished plate glass (not HSG (not printed, not TSG (not printed, not sand- Property printed, not sand-blasted) sand-blasted) blasted) Normal limit stress f as spec. k in DIN EN 572-1, DIN EN 1863-1 or abZ, 45 N/mm² 70 N/mm² 120 N/mm² DIN EN ISO 12150-1 Design coefficient k , normal 1.8 1 1 c k for laminated safety glass 1.1 1.1 1.1 LSG k (k ) for calculating the edge Kante 0.8 1 1 effect of glass edges Material factor γ 1.8 1.5 1.5 M permanent: 0.25 Modification factor for medium duration: 0.4 calculating the effect of load short: 0.7 durations Rated value of the resistance R = k * k* k * k * d mod c VSG Kante R = k* k * k * f / γ R = k* k * k * f / γ to stress failure R f / γ d c VSG Kante k M d c VSG Kante k M d k M The intermediate films in LSG shall be made of PVB or SGP (SentryGlas® plus). Films made of PVB must have a tear strength of at least 20 N/mm². SGP films shall have general approval by building authorities (including European Technical Approval ETA) and shall be processed in accordance with this approval. 3 STAND DESIGN, CONSTRUCTION AND LOADS 3.1 Vertical glazing not intended to prevent falling 3.1.1 Vertical glazing of a height h 4 metres above hall floor level Neither static proof of structural characteristics in accordance with the regulations specified in chapter 2.3 is required, nor is it necessary to submit documentation of testing. In this case the exhibitor alone is responsible for ensuring that the construction/design is technically safe for general use and that it meets current and accepted technical standards. Table A provides an overview of the types of structural designs that are possible. - Either TSG or LSG must be used. - The glass sheets may be secured by linear supports or at individual points. - Glass walls tilting at an angle of more than 10° from the vertical are considered to be overhead glazing for which the provisions of chapter 3.3 shall apply. - Additional measures, e. g. provision of static proof calculations similar to those described in chapter 3.1.2, may be required to ensure protection of neighbouring walkways, or to be able to bear the loads of persons leaning against or bumping into the glass. 3.1.2 Vertical glazing of height h > 4 metres above hall floor level Vertical glazing not intended to prevent falling and whose uppermost edges are higher than 4 metres above hall floor level does not require Installation approval for a specific case (c.f. 4.2) provided that the type of glass used, structural design details and the type of supports securing the glass comply with the regulations specified in chapter 2.3. In addition, the following provisions shall be observed. - Verified structural calculations or structural calculations suitable for verification and the corresponding construction plans must be submitted. - In addition to the load of its own weight, the material must be capable of resisting horizontal forces, i. e. a pressure corresponding to at least h1 = 0.125 kN/m² for visible surfaces of up 4 m above hall floor level and at least h2 = 0.063 kN/m² for visible surfaces at more than 4 m above hall floor level. Information sheet (Supplement to Technical Regulations, chapter 4.4.3) Use of glass and acrylic glass in stand construction and design inside trade fair halls Page 5 - Wherever there is a high risk of impact, e. g. where there is a descending ramp leading towards the glazing, additional measures are required. - Proof of structural characteristics is not required if the area of each individual sheets is less that 1.6 m² and TSG with a thickness of at least 4 mm is used, and the sheet(s) is(are) held on four sides by linear supports. Glazing secured at individual points may be used without further proof documentation if: - general construction approval (abZ) has already been granted for the combination of point-mounting method and glass type and thickness, or - the design specifications, and the dimensions and thickness of the glass as stated in TRAV, TRPV, DIN 18008-3, DIN 18008-4 or Table B are adhered to. TRAV, DIN 18008-3 / -4 and Table B are referred to above because the fall-prevention glazing barriers described in these references are of course also suitable for glass panels not explicitly intended to prevent falls. Installation approval for a specific case is required for all other designs. If the use TSG glazing is planned, a heat soak test certificate must be submitted. Table A provides an overview of possible designs and the necessary proofs. 3.2 Vertical glazing intended to prevent falls In all three of the following categories, A, B and C, static load proof calculations for the glass and the supporting structures and proof of the load-bearing capacity under impact-like conditions are required. The static structural design calculations for the glass and the supporting structure shall be based on an assumed cross-bar pressure load and as an additional load case, a horizontal assumed surface load of h1 = 0,125 kN/m² for all visible surfaces at up to 4 m above the hall floor level and of h2 = 0,063 kN/m² for surfaces located at more than 4 m above hall floor level. The load-bearing capacity of the structure under impact action can be verified as follows: - a pendulum impact test in accordance with DIN EN 12600 if design calculation concept A is used, or in accordance with DIN 18008-4 if design calculation concept B is used, or - the relevant design specifications, glass dimensions and thicknesses as stated in Table B of this information sheet are adhered to, or - by providing proof calculations in accordance with the rules described in chapter 2.3. Table B contains an overview of possible designs and the proofs required. All structural design details (including flexing/sag and glass insertion/clamping depths) shall be modelled in accordance with the rules described in chapter Pendulum impact tests must be carried out by one of the test centres/ínstitutes named in chapter 4 well in advance of the fair and outside the trade fair halls. 3.2.1 Category A – vertical glass wall Definition: Linearly-supported vertical glazing that does not contain any load-bearing bars at capping height and is not protected by a rail or cross-bar located in front of it, making it suitable for the direct action of rail or cross- bar loads, e. g. glazing of full room height. If protection is required to prevent persons falling from a height of more than 1 metre, then it will be necessary to refer to the Technical Regulations for the Use of Accident-Prevention (barrier) Glazing [Technische Regeln für die Verwendung von absturzsichernden Verglasungen (TRAV)] or DIN 18008-4. - Only LSG shall be used. - Verified proof of structural characteristics or static structural calculations suitable for verification, as well as a pendulum impact test (test in accordance with DIN EN 12 600 or DIN 18008-4) are required. - The pendulum impact test is not required for glass with linear support on all sides, provided that the appropriate dimensions and glass thickness conform to Table B (or TRAV 6.3. and Table 2), DIN 18008-3 and DIN 18008-4, or proof calculations are carried out in accordance with DIN 18008-4. - The glazing supports must provide adequate protection to the edges of the glass sheets. 3.2.2 Category B – clamped glass balustrade with continuous handrail Definition: Load-bearing glass balustrades held by linear supports secured by clamp-type base mountings, the individual glazing elements of which are connected by a continuous, load-bearing handrail (see example in chapter 6.1) attached to the top of the structure. - Only LSG shall be used. - Verified proof of structural characteristics or static structural calculations suitable for verification, as well as a pendulum impact test (test in accordance with DIN EN 12 600 or DIN 18008-4) are required. Information sheet (Supplement to Technical Regulations, chapter 4.4.3) Use of glass and acrylic glass in stand construction and design inside trade fair halls Page 6 - If LSG made of 2 x 10 mm TSG (or 2 x 10 mm HSG) is used, no pendulum impact test is required, provided that the dimensions as stated in Table B are adhered to (design details in accordance with TRAV or DIN18008-4). - The thickness of the intermediate PVB/SGP film must be at least 1.52 mm. - The securing clamps must be at least 100 mm above floor level. Calculations shall be provided proving that the loads will be distributed via the capping to neighbouring glass sheets in the event of an individual sheet being destroyed. The stresses occurring in the neighbouring glass sheets under the resulting conditions may then increase to 50 % above permissible limits if structural design calculation concept A was applied. If structural design concept B has been applied, this case can be classified as an extraordinary design calculation situation. The destroyed or damaged glass sheet shall be replaced immediately after the incident. 3.2.3 Category C – Railing and balustrade infills and glass walls with load-distributing cross-bar fitted in front of it Definition: Accident-prevention (barrier) glazing which is not intended to distribute capping loads and which corresponds to one of the following groups: C1: Railing/balustrade infills secured by linear supports and/or at individual points on at least two opposing sides. C2: Vertical glazing beneath a crosswise load-distributing spanning member located at capping level and secured by linear supports on at least two opposing sides. C3: Category A type glazing with a load-distributing cross-bar placed in front of it. - For category C1 and C2 type glazing, the use of TSG is allowed if the sheets are secured by linear supports on all sides. For all other types of supports and for category C3, only LSG may be used unless other statutory construction approval exists. - Table B contains an overview of possible designs and the proofs required. - The pendulum impact test is not required if the relevant design specifications and the dimensions and thickness of the glass as stated in Table B or TRAV or in DIN 18008-4 are adhered to. Alternative measures / protection against glass breakage: If the proof calculations for category C in accordance with TRAV or DIN 18008-4 are not submitted for accident- prevention (barrier) glazing, then the accident-prevention (barrier) attribute can be achieved by installing adequately sturdy knee-height cross-bars or steel rope of at least 5 mm diameter at a vertical spacing of not more than 35 cm and at an adequate distance in front of the glass infill sheets. Measures to protect against scattering glass splinters shall always be installed above and along the length of walkways, if this is not possible, LSG shall be used. 3.3 Horizontal glazing 3.3.1 Overhead glazing Glass walls tilted at an angle of more than 10° from the vertical are considered to be overhead glazing. Table C contains an overview of possible designs and the proof documentation required. Only the following glass products may be used: - LSG made with float glass (PPG) - LSG made of HSG, - Wire glass (only for existing components) In addition to submitting certification of load-bearing capacities, experimental proof of residual load-bearing capacities must be provided or, if this is not possible, a safety net must be hung under the glazing. If the structural design requirements of TRLV or as specified in DIN 18008-2 are met, proof of the residual load-bearing capacities in not required. The design loads to be assumed are the sheet's own weight and a horizontal pressure corresponding to at least h1 = 0.125 kN/m² for visible surfaces of up 4 m above hall floor level or h2 = 0.063 kN/m² for vertical visible surfaces at more than 4 m above hall floor level. The sheets must secured in such a way as to properly safeguard against them slipping out of the mounts and forces which may lift them off the mounts. The design dimensions of glass sheets mounted at individual points and HSG sheets shall either be calculated according to the rules outlined in chapter 2.3 or they must have general construction approval (abZ). If, for cleaning purposes, overhead glazing periodically has to support human loads, then such additional loads must be taken into consideration and experimental proof of residual load-bearing capacities must be provided [8]. In such cases a special individual construction approval is always required. – LSG sheets with an effective span exceeding 1.20 m shall be supported on all sides. The ratio between length and width may not exceed 3 to 1. The overall thickness of the intermediate PVB/SGP films must be at least 0.76 mm. If a sheet is supported on all sides, then a thickness of 0.38 mm is allowed under the condition that the length-to-width ratio is not greater than 3 to 1 and that the effective span in the direction bearing the main load is not greater than 0.8 m. Information sheet (Supplement to Technical Regulations, chapter 4.4.3) Use of glass and acrylic glass in stand construction and design inside trade fair halls Page 7 – The effective span of a wire glass sheet may not exceed 0.7 m, and the glass shall protrude into the supports by at least 15 mm. – Cutting of recesses or notches in the glass sheets is not allowed. – Only holes conforming to TRPV and/or DIN 18008-3 are allowed. – The maximum permissible sag shall not exceed 1/100 of the effective span between the closer supports of the sheet. 3.3.2 Glazing designed to support human loads This kind of glazing is specifically intended to be subjected to persons walking over it, e. g. stairs, platforms, landings and cat-walks. The design and proof calculations shall take both dead loads (own weight) and the working loads into account. In addition, proof of impact resistance and residual load-bearing capacity shall be provided. Proof of impact resistance and residual load-bearing capacities as a result of component tests must be submitted. The requirements are specified in [8] and in DIN 18008-5. For glazing mounted in linear supports at all four edges and an assumed working load of not more than 5.0 kN/m² for design calculations, proof of impact resistance and residual load-bearing capacity is deemed to have been provided if the sheets conform to the dimensions listed in Table 3. Table 3: Glazing mounted in linear supports at all four edges and intended to support human loads, with proven impact resistance and residual load-bearing capacity. max. max. LSG structure [mm] Minimum supporting length width: (top /*/ centre /*/ bottom) surface depth [mm] [mm] [mm] 1500 400 8 HSG /*/ 10 Float /*/ 10 Float 30 1500 750 8 HSG /*/ 12 Float /*/ 12 Float 30 1250 1250 8 HSG /*/ 10 HSG /*/ 10 HSG 35 1500 1500 8 HSG /*/ 12 HSG /*/ 12 HSG 35 2000 1400 8 HSG /*/ 15 Float /*/ 15 Float 35 /*/ = 1.52 mm PVB or SGP (SentryGlas® plus) intermediate film layer Glazing designed to support human loads may be secured by linear supports or at individual points. It must be made of LSG consisting of at least three layers of TSG and/or HSG/float glass. From the point of view of impact resistance, the use of TSG or HSG for the top layer is recommended. This surface must possess non-slip characteristics in accordance with DIN 51097. In order to achieve the required residual load-bearing capacity, the two lower layers will normally be made of float glass or HSG. Information sheet (Supplement to Technical Regulations, chapter 4.4.3) Use of glass and acrylic glass in stand construction and design inside trade fair halls Page 8 Glazing, mountings and supporting structure must be designed and their dimensions calculated to withstand the load of their own combined weight (dead load) as well as intended human (working) loads in accordance with the chosen design calculation concept and all relevant and applicable standards. Design calculation concept A (TRLV) B (DIN 18008-5) Working surface load q , depending on C1: 3.0 kN/m² C1: 3.0 kN/m² k usage category C3, T2: 5.0 kN/m² C3, T2: 5.0 kN/m² Point load Q , as an additional k C1: 4.0 kN C1: 4.0 kN changing load parameter to be C3: 4,0 kN / T2: 2.0 kN C3: 4,0 kN / T2: 2.0 kN investigated Application area of point load 100 x 100 mm 50 x 50 mm only for constant design Inclusion of top sheet in structural static no situation and for temporary calculations allowed design situation Proof calculation for situation with proof for an extraordinary broken top sheet (i. e. only the two standard proof design load calculation lower sheets still bear the load) situation DIN EN 1991-1-1 DIN EN 1991-1-1 Standards relating to the action of loads DIN EN 1991-1-1 /NA DIN EN 1991-1-1 /NA Max. sag / flexure with 3 load-bearing l/200 l/200 sheets Max. sag / flexure with 2 load-bearing l/100 l/100 sheets In the case of stairways the construction/design must guarantee sufficient distribution of loads. Stairs on stand structures shall always be classified with usage category T2. 4 APPROVAL PROCEDURES 4.1 Basics If a glass component and its glass products conform to the technical building regulations outlined in chapter 2.3 and to generally accepted technical principles, then it shall be sufficient to submit the verified structural calculations and the verified plans, following which construction approval will be granted. In addition, the construction work on site will be checked and the results subjected to an approval inspection. If additional components are installed for which statutory construction approval, a statutory construction test report or type approval are required, then these documents are to be submitted together with the structural calculations. If a glass component or parts of this component do not conform to the construction engineering regulations and generally accepted technical principles outlined in chapter 2.3, and if no statutory construction approval or statutory construction test certificate can be produced, then an individual construction approval (Zustimmung im Einzelfall – ZiE) shall be required. An Installation Approval for a Specific Case may be granted instead of the individual construction approval if glass is used only within the rules and limitations described in this information sheet. 4.2 Installation approval for a specific case This approval procedure is similar to the procedure for obtaining individual construction approval. If an Installation Approval for a Specific Case has been granted once for a particular construction/design and type of usage, then the trade fair companies in question will accept this for an identical design serving an identical purpose. Nevertheless, a new application for construction work approval and approval inspection shall be submitted for each repeated case. The test report, all certificates and approvals, design details, as well as glass dimensions and thicknesses must be submitted with the application. Glass components requiring approval and which require type 3 proof documentation are listed in column 14 of Tables A, B and C. Installation approvals for specific cases cannot be granted at short notice, as they require a considerable period of time for processing. Applications for these should therefore be submitted at least 6 weeks before the commencement of construction. Prior to conducting component tests, it is advisable to contact the relevant trade fair company in good time in order to coordinate procedures and intended testing methods. Normally, component testing requirements stipulate inclusion of parts of the glass component’s actual substructure in order to simulate realistic loads. Information sheet (Supplement to Technical Regulations, chapter 4.4.3) Use of glass and acrylic glass in stand construction and design inside trade fair halls Page 9 The procedure for obtaining an Installation Approval for a Specific Case is as follows: The structural calculations and the required certificates confirming the identity of the product(s) (glass manufacturer/processing company's factory certificates) must be verified and checked by a publicly certified structural building surveyor and tester (in the field of steel, concrete and brick construction/engineering). The surveyor shall confirm that there are no objections with regard to the design's suitability for use. It is his responsibility to decide on the necessity of additional testing of materials, impact resistance and whether further proof of residual load-bearing capacities must be obtained. The test report must be submitted to the trade fair company along with the other application documents requesting construction work permit (construction permit) and subsequent monitoring of the stand construction work and stand approval inspection. Final approval will be granted on location following an inspection to confirm that the construction/design on site conforms to the previously inspected documents. The engineer carrying out the monitoring and inspection acts on behalf of the trade fair company. Recommended institutes for testing components used in glass construction/design: Technische Universität Dresden, MFPA Leipzig GmbH TU Hamburg - Harburg Institut für Baukonstruktionen (Beyer- Hans-Weigel-Str. 2B Institut für Baustatik und Stahlbau Bau) 04319 Leipzig Prof. Dr.-Ing. Starossek Prof. Dr.-Ing. Weller Denickestr. 7 George-Bähr-Str. 1 21073 Hamburg 01069 Dresden Institut für Massivbau Materialprüfanstalt für das Bauwesen MPA Nordrhein-Westfalen Prof. Dr.-Ing. Marx Braunschweig Marsbruchstr.186 Leibnitz-Universität Hannover Beethovenstr. 52 44287 Dortmund Appelstr. 9a 38106 Braunschweig 30167 Hannover RWTH Aachen MPA Darmstadt TU Darmstadt Lehrstuhl für Stahlbau Grafenstr. 2 Institut für Werkstoffe und Mechanik Prof. Dr.-Ing. Feldmann 64283 Darmstadt im Bauwesen Mies-van-der-Rohe-Str. 1 Prof. Dr.-Ing. Wörner 52074 Aachen Petersenstr. 12 64283 Darmstadt FMPA Baden-Württemberg Universität Karlsruhe Friedmann & Kirchner FB 2, Abt. 21, Referat 214 Versuchsanstalt für Gesellschaft für Material- Pfaffenwaldring 4 Stahl, Holz und Steine und Bauteilprüfung 70569 Stuttgart (Vaihingen) Prof. Dr.-Ing. Ummenhofer Große Ahlmühle 7 Otto-Amman-Platz 1 76865 Rohrbach 76131 Karlsruhe FH München TU München Institut für Fenstertechnik e.V. Labor für Stahl- und Leichtmetallbau Lehrstuhl für Stahlbau Theodor-Grietl-Str. 7-9 Prof. Dr.-Ing. Bucak Prof. Dr.-Ing. Mensinger 83025 Rosenheim Karlstr. 6 Arcisstr. 21 80333 München 80333 München Information sheet (Supplement to Technical Regulations, chapter 4.4.3) Use of glass and acrylic glass in stand construction and design inside trade fair halls Page 10 5 NOTES ON DESIGN AND DESIGN CALCULATIONS - Glass is a brittle material, any failure of which will occur spontaneously and without warning. - Glass is sensitive to blows with hard, pointed objects. These properties lead to the following guideline notes: - Proof calculations for the load-bearing capacity of structural glass not only take into consideration the unbroken glass but always include an investigation of the broken or partially broken glass (proof of residual load-bearing capacity). - The support design must ensure that glass sheets are not subjected to pressure or stresses by the supports. - Direct glass-to-glass contact and contact between glass and other hard materials (e.g. metal) shall be prevented at all times, whereby the effects of load and temperature fluctuations have to be taken into account. - The minimum supporting depths of glass sheets (“glass insertion depth”) on their respective support sections as well as the allowable sheet and supporting beam sections as specified in the standards listed in chapter 2.3 for the selected design calculation concept must be adhered to. - After glazing has been installed, the markings identifying the individual type of glass sheet used (e.g. TSG, HSG) must be durable and legible at all times. In the case of LSG glazing, a section of the edge must be left free for inspection purposes (to check the number of glass sheets, thickness, interlayer films) until the construction has been approved. If required, a manufacturer's certificate shall be submitted as well. - The edges of glass sheets must be finished or protected in such a way as to exclude any possibility of injury. - In the case of TSG, HSG, or LSG glazing manufactured from sheets of TSG or HSG, subsequent reworking of the finished product such as cutting out sections or drilling holes is not possible. - Sheets intended to bear human loads must have a durable non-slip surface finish. - Load-bearing adhesive joints may only be used if a general construction approval (abZ) has been granted for the entire adhesive system (i. e. the glass, adhesive and metal combination), and under the condition that the joint is made exactly as described in the approval documents. - The rules described in chapter 2.3 do not yet make allowance for applying more favourable assumptions of the joint effect of the intermediate film layers in LSG and therefore an Installation Approval for the Specific Case has to be applied for if these assumptions are used in calculations. Trade publications [18] contain information on suitable calculation assumptions to account for the joint effects in LSG. This may possibly be useful for LSG in which SGP is used. 6 EXAMPLES OF STRUCTURES (BARRIERS) DESIGNED TO PREVENT FALLS All possible dimensions, types of glass, thicknesses and the necessary proof documents are summarised in Table B. 6.1 Category B Geländerhöhe gemäß Technische Richtlinie beachten ! Handlauf / Railing cap height must conform to handrail technical guideline ! Note: If LSG made of 10 mm TSG + 1.52 mm PVB/SGP + 10 mm TSG or of 10 mm HSG + 1.52 mm PVB/SGP + 10 mm HSG in the dimensions as stated in Table B is used, only static structural proof calculations are required. As specified in TRAV or DIN 18008-4, this also applies to parallelogram-shaped balustrades.
Description: