Gen II Tesla Model S   Lighted Rear Applique  Installation Instructions Parts Needed • Gen II aluminum lighted Rear Appliqué with Bluetooth controller (purchase on ​​ evappliques.com) Parts provided with the Appliqué include: • The lighted applique with TESLA 3D printed letters and neopixel PCB letter board installed • Bluetooth controller with Velcro on back for attachment to underside of trunk liftgate • Parachute thread for removing stock applique • Spare plastic rivets for liftgate trim (in the event the stock rivets are lost or broken) • 15 feet CAT6 cable or rainbow ribbon wire • 10 feet red and black 18 gauge wire • 8 PosiLok Connectors • 6 PosiTaps • 1 pad 3M automotive adhesion promoter Tools/parts needed: • Pull tool such as thin fiberglass rod, coat hanger wire, or music wire rod, about 24 inches long (1/2M) and less than 1/16 inch (1.5MM) in diameter. • Wire cutters or scissors • Wire stripper • Plastic pry tool • Goo Gone Spray Gel • #15 Torx bit and wrench • Dremel tool with cut-off disc • ETS International HCT-1200 12V Hookie Circuit Tester (available on Amazon.com) ​ As Tesla often changes wire colors, the suggested wire color connections in these instructions may be wrong. This tool is essential for making the correct connections - it enables testing of the wires that are linked to the controller and trigger the the applique lighting effects such as reverse or turn signals  • TESLA MODEL S LIGHTED APPLIQUE INSTALLATION V1.3 PAGE 1 Summary of Key Installation Steps For those upgrading from or replacing a GEN I applique Follow the instructions below for removing the existing applique.. Carefully and completely remove all of the 3M tape residue. Follow the applicable instructions below for mounting the new Gen II applique. There is no need to do any additional wiring. Your new GEN II applique will work with your currently installed controller. Once the new applique is mounted all you need to do is connect the three wire leads from the controller and Gen II applique and it will be fully operational. For those doing a complete install of the GEN II applique 1. Applique • Remove existing appliqué  ​ • Loosen and modify the black plastic mounting bracket under the appliqué ​ • Re-tighten the mounting bracket and install the new appliqué ​ 2. The Controller • Remove all the plastic trim on the underside of the liftgate • Remove the trim from the right side of the trunk • Loosen the rear of the trim on the left side of the trunk • Place the Appliqué Controller module just inside the hole for the left pulldown handle. ​​ • Locate and tap with the PosiTap connectors 12V, ground, reverse, brake, running light, right and left turn connections in liftgate and trunk. Attach the 18AWG wires to the 12v and ground taps then attach the appropriate color wire in the rainbow cable to the reverse, brake, running, and left and right turn taps. See below for detailed instructions • Run all of these connecting wires to liftgate left handle area, attach PosiLok connectors to the loose controller wire ends, and connect them to appropriate 12v, ground, brake, right and left turn, and running leads, then test all of the functions to be sure operation is ok. • Velcro the controller inside the liftgate. 3. Testing • Set and test any desired configurations via the Bluetooth interface.   4. Re-install all trim TESLA MODEL S LIGHTED APPLIQUE INSTALLATION V1.3 PAGE 2 Note: If you are doing the installation yourself you may want to review these ​ supplemental installation notes provided by JPP.   ​ TESLA MODEL S LIGHTED APPLIQUE INSTALLATION V1.3 PAGE 3 A. Mount the Appliqué 1. Raise the lift gate to a convenient working level for working on the appliqué 2. Remove the existing appliqué: Each end ​ of the appliqué has two-sided tape attached to the reverse light. Using the parachute cord supplied or similar to saw/cut this tape loose. As you work the cord will stop at the first right and left attachment clips, about 2-3 inches from the tail light sides. After both ends are free, use your hands or a plastic trim tool to carefully pry the appliqué straight back and release the the clips, There is quite a bit of two sided tape, and four clips that can need to be released. Work slowly and carefully. It should not take great force, once the tape is cut or pried loose. 3. Modify the black plastic mounting bracket under the appliqué. The black ​ plastic mounting bracket is held by three or four T15 screws that are accessible from the underside of the bracket. Remove these screws as well as the two screws holding the camera in place. Keep careful track of the screws, as they are different for the bracket and the camera. It is NOT necessary to remove the lenses on the reverse lights, but you may want to remove the license plate and frame to provide more working room. Then loosen the bracket so you can pull it away from the liftgate. Refer to the the large photo below to determine the sections of the bracket that must be cut. Then mark the cut lines TESLA MODEL S LIGHTED APPLIQUE INSTALLATION V1.3 PAGE 4 with blue painters tape. As you pull the bracket away from the tailgate sheet metal, use the Dremel tool and cut along the marked lines, taking care not to cut into the sheet metal or paint as you cut the bracket. Discard the cut pieces. 4. Test fit the new appliqué. Clean ALL two sided tape residue from the black plastic bracket and the tail lights. To assist with removal soak the tape with Goo Gone Spray Gel or other safe glue removers for at least 5 minutes. Using a plastic pry tool helps with removal of the tape. Additional layers of Goo Gone may be necessary. After all of the tape residue has been removed, clean the entire black plastic bracket surface with denatured alcohol. Then rub the 3M adhesion promoter on the indented spaces for the applique on the tail lights . As the Gen II applique’s four top clips and five bottom clips snap it firmly into place, it is not necessary to use any 3M double sided tape on the black plastic bracket to mount the applique. The GEN II applique comes with 3M sealant tape TESLA MODEL S LIGHTED APPLIQUE INSTALLATION V1.3 PAGE 5 on the end. This will be used to make a more secure connection of the ends to the taillights If you’ve detached the camera from the bracket, use the original screws to tighten down the camera and applique bracket. The connecting cable of the appliqué is inserted into the rectangular opening in the bracket closest to the cable position itself (that opening goes through the entire liftgate shell and make the cable available from the interior side of the liftgate). There are two methods for final mounting of the applique, as described below. Method 1: Work from left to right. Remove the red 3M tape liner from all of the tape on the two applique ends. Insert the power cord into the trunk, pull the cable into the trunk as you start to align the applique . Then align the four upper clips in their respective slots on the liftgate but do not snap them into place. Take care to not let the tape on the two ends touch the tail lights. When you are satisfied with the alignment start with the left end of the applique and push it firmly onto the tail light so the tape adheres. Then working from the left side, snap the four upper clips into place firmly, finishing by placing the right side end firmly onto the tail light until the 3M tape adheres. Then using firm pressure make sure the lower and upper clips are also snapped into place. Method 2: Align and snap into place the four upper clips Remove the red 3M tape liner from all of the tape on the two applique ends. Then align the four upper clips in their respective slots on the liftgate but do not snap them into place. Take care to not let the tape on the two ends touch the tail lights. When you are satisfied with the alignment snap the four upper clips into place firmly. The check the alignment of each end and push the them firmly into place on the tail lights so the 3M tape adheres. Then using firm pressure make sure the lower clips are also snapped into place. For now this completes the work on the outside of the car. Time to move inside. TESLA MODEL S LIGHTED APPLIQUE INSTALLATION V1.3 PAGE 6 B. Remove liftgate trim pieces There are four black plastic trim pieces on the interior side of the liftgate: top, right and left sides, and a large piece covering the lower side of the liftgate. Each is clipped into place with plastic retainers that snap into a hole on the lift gate metal frame. These must be removed to proceed with the installation. If you break or lose any of these retainer clips replace them with the clips provided in the installation kit of parts.    1. Begin with upper horizontal piece. Using a plastic pry tool or your hands, snap the right or left side loose and remove the piece. This piece pulls straight “down”. Some of the clips may break or remain stuck in the hole. In the latter case use a u-shaped pry tool to remove them. Save all the clips that have not been damaged —  ​ you’ll need them for the re-installation. ​​ Replace any broken clips with those in the parts kit. 2. Do the same with the right and left pieces. These pieces DO NOT pull straight “down”; instead, they pull straight “in” toward the center of the window on a horizontal plane. Pulling down will break the clips. Removal of the large bottom trim piece requires several additional steps, as follows.. First, the two indented handle openings at the bottom of the piece have to be removed using a pry tool. The passenger side handle opening has a wire connection for the liftgate release. Unplug it. The large lower trim piece has several electric connections on the back side: one each for the two rear speakers, one for the trunk light, and for the rear beeper. We recommend having a second person help as you work with this piece. The work is easier if you first remove the horizontal TESLA MODEL S LIGHTED APPLIQUE INSTALLATION V1.3 PAGE 7 plastic speaker deck at the top of this section. This deck holds the two rear speakers and is attached with several screws. Remove the screws and disconnect the two speaker connections. The large lower piece also has several electric connections on the back side: one for the trunk light, and for the rear beeper. We recommend having a second person help as you work with this piece. Each of these connectors must be unplugged, and each uses the same black plastic connector that has a latch that must be released to unplug the connector. Note also that there is a T15 screw at the “tip” of ​​​​ each side of this big piece, and there are eight to ten clips holding it in place. Remove these T15 screws. Then starting with the bottom edge work the trim piece loose but hold it loosely in place once all of the retaining clips have been released, taking care not to stress or break the electrical connectors. Reach up over the inside of the trim pieces to disconnect them. You will need your helper to hold the trim piece while you release these connections. IMPORTANT: On at least some cars, the wire leading to the warning beeper, mounted in the center of the speakers, has a different plastic connector. The latch for this connector can only be released with a small screwdriver, pushed straight down into the top of the body of the connector (NOT near the end like the other latches). Unfortunately, the speaker deck prevents you from seeing this, and makes it very awkward to push the latch with a screwdriver. This is why removal of the speaker deck is recommended. Note: Connectors with  the black locking tab can be popped loose with your finger from ​​ behind the connector. The white locking tab must be pressed down from between the “rails” of the connector, not from the rear. It’s also possilble that on new Model S these ​​ connections have been made improperly at the factory TESLA MODEL S LIGHTED APPLIQUE INSTALLATION V1.3 PAGE 8 3. When the pieces have been removed you may see (depending on your car) two black vinyl sheets on the back of the lift gate. These are glued on with a tar-like material and need to be removed to provide access to the electrical connections. Remove them and set aside. 4. Once all of the trim pieces have been removed set them aside in a safe place and keep all of the retainers and screws in a place where they will be easy to find for reuse. Replace any broken plastic clips. C. Install the Bluetooth controller and make the power supply, brake, reverse, turn signal, and running light connections TESLA MODEL S LIGHTED APPLIQUE INSTALLATION V1.3 PAGE 9