l a u n a M l a c i n Compact h HF SSB DSC c Watchreceiver e T Valid for: RM2152 2152 Overview of RM2152 The RM2152 may have a number of names, depending on whether it is a SAILOR, NORCONTROL, Husun or Sperry product. In this manual, however, only the SAILOR names are used. The table below shows the different names used for each unit, emphasizing the SAILOR names Compact HF SSB DSC SAILOR NORCONTROL Husun Sperry Watchreceiver RM2152 RM2152 RM2152 2152 RM2152 Please Note: Any responsibility or liability for loss or damage in connection with the use of this product and the accompanying documentation is disclaimed. The information in this quick guide is furnished for informational use only, is subject to change without notice, may contain errors or inaccuracies, and represents no commitment whatsoever. This agreement is governed by the laws of Denmark. Doc. No.: M2152COM Issue: B/0211 RM2152 CONTENTS 1 GENERAL INFORMATION 1-1 1.1 INTRODUCTION 1-1 1.2 GENERAL DESCRIPTION 1-1 1.3 TECHNICAL DATA 1-2 1.4 CONTROLS 1-4 1.5 PRINCIPLE OF OPERATION AND BLOCK DIAGRAM 1-6 2 INSTALLATION 2-1 2.1 MOUNTING POSSIBILITIES 2-1 2.2 DIMENSIONS AND DRILLING PLAN 2-3 2.3 INSTALLATION INSTRUCTION 2-8 2.3.1 INSTALLATION OF DSC/TELEX MODEM RM2152 IN EXISTING TRANSMITTER SYSTEMS 2-8 2.3.2 INSTALLATION GUIDE FOR RM2152 USED AS DSC WATCH RECEIVER 2-10 2.3.3 INSTALLATION GUIDE FOR RM2152 USED AS DSC/TELEX RECEIVER 2-13 2.4 ELECTRICAL CONNECTIONS AND ASSEMBLING 2-18 2.4.1 HF SSB 250W DC WITH DSC WATCH RECEIVER RM2152 and N2165 2-18 2.4.2 HF SSB 250W DC WITH DSC WATCH RECEIVER RM2152, RADIOTELEX MODEM RM2152 AND N2165. 2-21 2.4.3 HF SSB 600W AC/DC WITH DSC WATCH RECEIVER RM2152. 2-24 2.4.4 HF SSB 600W AC/DC WITH DSC WATCH RECEIVER RM2152, RADIOTELEX MODEM RM2152 AND N2165. 2-27 2.5 APPENDIX 2-31 2.5.1 ANSWERBACK CHARACTER SETTING 2-31 2.5.2 MAIN PROCESSOR BOARD VERSION 4 DIP SWITCHES 2-32 2.5.3 MAIN PROCESSOR BOARD VERSION 3 DIP SWITCHES 2-32 0135 RM2152 CONTENTS 1 GENERAL INFORMATION 1-1 1.1 INTRODUCTION 1-1 1.2 GENERAL DESCRIPTION 1-1 1.3 TECHNICAL DATA 1-2 1.4 CONTROLS 1-4 1.5 PRINCIPLE OF OPERATION AND BLOCK DIAGRAM 1-6 0135 RM2152 1 GENERAL INFORMATION 1.1 INTRODUCTION Compact HF SSB RM2152 is the DSC and TELEX scanning receiver with built-in DSC and TELEX modem. It has been developed on the basis of SAILOR‘s many years of experience with short wave communica- tion equipment. It has the same high reliability as all SAILOR equipment is known for. It has been constructed so that it fits in with other units in the Compact Programme 2000. SAILOR HF SSB PROGRAMME 2000 CONSISTS OF THE FOLLOWING UNITS: RE2100: Control unit with integral receiver and exciter. T2130: 250W PEP SSB transmitter with integral power supply for RE2100. Supply voltage 24V DC. AT2110: 250W PEP aerial coupler for outdoor use. N2160: 12V DC power supply for T2130. N2161: 110/220/240V AC, 50 Hz power supply for T2130. N2165: AC/DC power supply for RM2152 1.2 GENERAL DESCRIPTION RM2152 - is an all solid state constructed microcomputer controlled SSB short wave radio modem. - covers the frequency range 100 kHz to 30 MHz. - is a scanning receiver with integral DSC and TELEX modem. - has a special serial input/output (SP-BUS) enabling RM2152 to communicate with the other units in the Compact 2000 programme. - is fully synthesized and has a high stability reference oscillator (TCXO). - has an- easy-to-read display with controlable backlight. - has a push-button keyboard offering an attractive tactile feeling and a safe finger-guide in the metal front. The keyboard is fitted with night-illumination of the lettering. - is a fully automatic ARQ telex unit with HF SSB RE2100 and the terminal equipment H2098A/ H2099/H1253B. The terminal equipment can be replaced by a personal computer. - is a fully automatic DSC unit with HF SSB RE2100. - has a read-out in alpha numerical display of received DSC information. Printer not necessary. - has easy to understand menu-controlled DSC calls. 0135 PAGE 1-1 1 GENERAL INFORMATION RM2152 1.3 TECHNICAL DATA SYSTEMS SPECIFICATIONS Communication protocol DSC: CCIR Rec. 493-9 (class A), 541-8. ETS 300 338, IEC 945. Telex: CCIR Rec. 625, 476-3, 490, 491(1978), CCITT Rec. 130. Other Rec’s: In compliance with ETSI, CEPT, MPT, FTZ and FCC. Modes of operation: ARQ, FEC, SELEC, and DSC. Line signal: Two tone keyed, 100 baud synchronous. DSC: 10 unit code, 7 bits information and 3 bits parity. TELEX: 7 unit code, constant 4B/3Y ratio. Call codes: DSC: 9 digits station inditification. TELEX: 5 digits and 9 digits with dual ship ID-codes for individual and group calls. Keys: All keys are back-illuminated. Display: ” Graphic LCD display with adjustable backlight angle. Acoustic Alarm: DISTRESS and URGENCY alert, alert for other type of received calls. Warning for wrong or missing entries. Scanning facilities: 10 scan programmes containing up to 6 different frequencies. Call stacks: The 5 last received ordinary calls. Not older than 48 hours. The 20 last received DISTRESS calls. Not older than 48 hours. Program memory: 384 kilobyte main memory in EPROM. 512 kilobyte volatile RAM. 64 kilobyte Nonvolatile RAM (battery back-up). 32 kilobyte Nonvolatile EEPROM. RECEIVER SPECIFICATIONS Receive System: Double conversion super heterodyne 1st IF 70 MHz. 2nd IF 10.73 MHz. Frequency Range: 100 kHz to 29999.9 kHz. Antenna impedance: 50 (cid:1) Frequency Stability: Better than 0.39 ppm. IF selectivity: Passband ripple better than 1 dB. 3 dB bandwidth at ± 150 Hz to ± 350 Hz. 60 dB bandwidth at ± 750 Hz. Sensitivity: DSC calling sensitivity -18 dB/V. TELEX calling sensitivity -18 dB/V. (CEPT method of test.) Adjacent Channel: 40 dB at ± 500 Hz. Selectivity: (CEPT method of test). Automatic gain control: Less than 2 dB variation of detector output level for 90 dB input signal variation. (0 dB/V to 90 dB/V) Fast attack time and slow decay time. PAGE 1-2 0135 1 GENERAL INFORMATION RM2152 Blocking: Better than 55 dB for unwanted signals in the band 1 kHz to 3 kHz away from the wanted signal. Better than 75 dB for unwanted signals more than 3 kHz away from the wanted signal. (CEPT method of test) Co-channel rejection: Less than 6 dB. (CEPT method of test). Intermodulation: IP3 better than 8 dBm. (CEPT method of test). Spurious and IF Rejection: Better than 70 dB. (CEPT method of test). Spurious Emission: Better than 1nW at antenna connector. Audio Power: 1 Watt into 8 ohm, less than 10% distor. LOCAL INTERFACE Printer interface: Parallel centronics. Remote control: CCITT Rec V.10 SPECIAL (RS-423, T-BUS), multidrop addressing for control of transmitter and data equipment control/polling. Navigator interface: NMEA 0183. Terminal interface: CCITT Rec. V.24/V.28 (rs-232C) External alarm: Alarm output, rs-410 type N (open drain). LINE INTERFACE Tone frequencies: 1700 ± 85 Hz, accuracy within 0.5 Hz. Modulation: Phase-continues AFSK keying. Frequency stability: Better than 0.1 Hz. Filter tracking: Adaptive tracking within ± 85 Hz. Decision filtering: Bit-slicing with multipath correction. Demodulation filter: 4 pole bessel. RX-tone input: Strap selectable internal/external. +10 dBm to -20 dBm, continues adjustable, 600 Ohm balanced. RX dynamic range: 35 dB. TX-tone output: +10 dBm to -20 dBm, continues adjustable, 600 Ohm balanced. Free-signal detection: Automatic detection and handling of free-signals. Radio control input: RS-410 type N. Radio control output: RS-410 type N (open drain). 0135 PAGE 1-3 1 GENERAL INFORMATION RM2152 GENERAL DC power source: +18Vdc ± 5%, 0.5 Amp. -18Vdc ± 5%, 0.2 Amp. +9Vdc ± 5%, 0.5 Amp. Ambient temperature: -15°C to 55°C operating. -20°C to 70°C storage. Relative humidity: 95% non-condensing. Vibration: IEC, CEPT and MPT 1204. Dimension: H*W*D, 98 mm * 210 mm * 300 mm. Weight: 3.7 Kg. 1.4 CONTROLS COMPACT HF SSB DSC WATCHRECEIVER RM2152 S.P. RADIO DENMARK VOL ABC DEF GHI O F 1 2 3 F JKL MNO PQR 4 5 6 STU VWX YZ- RX FUNC SCAN MSG EDIT LAST NEXT 7 8 9 DEG STOP DIS TRESS 2187.5 CALL SEND . 0 ENT 37151A VOL Volumen control and on/off switch for the mains. O F F Access to the functions <Display>,<Pos>,<Stns>,<Time>, FUNC <Test>,<Options>,<Print> and <Sun>. <Display>: Give access to the display set up menu. <Pos>: Give access to the postion set menu. <Stns>: Give access to key data in the station table. <Time>: Give access to set the internal clock. <Test>: Give access to the internal/external test menu. <Options>: Give access to the radiomodem set up menu. <Print>: Give access to a printer set up and a print menu. <Sun>: Give access to key in the number of sun-spots, used in the MUF-program. PAGE 1-4 0211