Emergency Lighting Interface LUT-ELI-3PH | Installation Guide Please read this guide before installing. Listing The Emergency Lighting Interface – LUT-ELI-3PH is Contents Page UL924 Listed as “Emergency Lighting and Power Ratings and model number overview ............................1 Equipment”. The interface shall be used with: Lutron Mounting the Interface .................................................2 GRAFIK Eye GP, XP, and LP panels; LCP128 panels; Wiring Overview for LUT-ELI-3PH units on: Softswitch128 panels; EcoSystem; Quantum; GRAFIK RadioTouch Systems ...............................................2 Eye QS, RadioTouch controllers, and Energi Savr Panel-Based Systems ..............................................4 Node units. EcoSystem or Quantum bus supplies.......................8 GRAFIK Eye QS units ...............................................9 Description Energi Savr Node units ..........................................10 The LUT-ELI-3PH unit senses the line voltage on Emergency Power Mode Setup: LCP Panels ..............11 all three phases or a single phase and controls the NEC Class 2/PELV Wiring to Fire Alarm emergency signal to the following compatible Lutron Control Panel (FACP) .............................................12 products/systems: Troubleshooting • Circuit Selector for GP, LP, XP panels RadioTouch ............................................................13 • LCP/XPS controller for LCP128, and Panel Based Systems ............................................14 Softswitch 128 panels Energi Savr Node Installations ................................15 • EcoSystem Bus Supply EcoSystem or Quantum System ............................16 • Quantum Bus Supply Grafk Eye QS Installation .......................................17 • Grafk Eye QS unit • RadioTouch controller • Energi Savr Node unit When one or more phases of normal power are lost, the LUT-ELI-3PH unit sends a signal to the affected device(s), activating the emergency mode. Any lights controlled by these devices will go to the emergency light level setting (factory set to 100% intensity). When normal power is restored, the lights will return to their previous intensities. Important Safeguards • Follow all national and local electrical codes and safety standards. • Turn off power before installation. • Line voltage input to the LUT-ELI-3PH unit must be GND from the NORMAL (non-essential) power source. 12 11 10 C9LASS8 2 LOW7 VOLT6AGE W5IRING4 3 2 1 S1 • Read and follow all safety instructions. • For indoor use only. • Equipment should be mounted in locations and at heights where it will not readily be subjected to System Ratings tampering by unauthorized personnel. • Voltage: 100-347 V 50/60 Hz 30 mA • Do not use this equipment for other than intended use. • Current: 20 A maximum circuit breaker • All servicing should be performed by qualifed service personnel. For use with Lutron®: GRAFIK Eye® GP, LP, and XP panels; LCP128TM panels; Softswitch128 panels; System Limits (per / LUT-ELI-3PH) EcoSystem® lighting control system; Energi Savr • 32 circuit selectors NodeTM units; Quantum® systems; GRAFIK Eye QS • 100 RadioTouch Controllers units, and RadioTouch® lighting controllers. • 32 EcoSystem bus supplies Note: This device does not provide emergency power. • 32 Quantum bus supplies An Emergency (Essential) power source must be • 32 Energi Savr Node units provided. • 32 LCP/XPS Controllers LUT-ELI-3PH Installation Guide Lutron® | 1 SENSE DRAIN MUX MUX +24VFW COMMON ´CFOACNPT´A NC/TCS C´FOACNPT´A NC/TOS NOT USED RADIOTOUCH PH F TAECSETF LED132 Emergency Lighting Interface LUT-ELI-3PH | Installation Guide Side View Mounting the Interface (Cross-Section) 1. Turn power off. 2. Wire the line voltage leads that protrude from back of 4 x 4 in LUT-ELI-3PH unit into the junction box. (102 x 102 mm) Junction Box 3. Mount the LUT-ELI-3PH unit onto a 4 x 4-inch (102 x 102 mm) junction box (not included, but available; Lutron part number 241-496). 4. Be sure all the power wires are completely inside the junction box before tightening the mounting screws. 5. Remove front enclosure cover to expose the terminal LUT-UENLIT-3PH blocks, test switch, and status LEDs. 6. Insert the NEC® Class 2/PELV wires through knockouts WALL in the LUT-ELI-3PH enclosure as shown in the diagram. 7. Connect the NEC Class 2/PELV wires to the Lutron® product or system, which the LUT-ELI-3PH will be Insert NEC Class 2/PELV controlling. Specifc wiring to these devices will be wires through knockouts described in the following sections. 8. Reinstall front enclosure cover. Note: Call the Lutron Technical Support Center at (800) 523-9466 for restrictions and wiring requirements for emergency fxtures (fxtures that never turn off or have a battery backup ballast in the fxture). Installing a LUT-ELI-3PH Unit in a RadioTouch® System Line Voltage Connections WARNING! Danger of shock. May result Note: Provide proper short-circuit and overcurrent in serious injury or death. DO NOT WIRE protection at the distribution panel. Maximum circuit WHEN LIVE! Switch off power to all power breaker rating of 20 A. feeds via circuit breaker or isolator before wiring or servicing the LUT-ELI-3PH unit and RadioTouch System Buttons and LEDs in the unit are used for troubleshooting. If wiring is exposed when accessing buttons and LEDs, the unit must be accessed by a certifed electrician, following local codes. Single-Phase Wiring Three-Phase Wiring Ground Ground Neutral Neutral Hot Phase C Phase B Phase A Normal Normal Power Power Figure #1 Figure #2 Lutron® | 2 LUT-ELI-3PH Installation Guide Red Red Red White Green Normal Lights Red Red Red White Green Normal Lights Emergency Lighting Interface LUT-ELI-3PH | Installation Guide Installing a LUT-ELI-3PH Unit in a RadioTouch® System (continued) NEC® Class 2/PELV Connections Test the System Note: When wiring for a backup/emergency source of Please perform the following tests to ensure proper power, the RadioTouch Controller (models RTA-RX-F, installation. RTA-RX-F-SC, RTA-RXSW), being used for the backup/ emergency lights (Unit A and B) cannot be controlled by 1. Turn off one of the Normal (Non-Essential) phase(s) an occupancy sensor. Units A and B DIP switch 2 must breaker(s) that the LUT-ELI-3PH unit is monitoring. be in the down position. You should see the following: • All lights controlled by Emergency (Essential) panel NEC Class 2/PELV Wiring to RadioTouch will go to FULL INTENSITY (factory set). Controllers • PHASE ON/OFF status Indicator (green) will turn One LUT-ELI-3PH can be connected in parallel with up OFF as the above test creates a phase failure. to 100 RadioTouch Controllers. • Upon turning the breaker back on, all lights should 1. RadioTouch Controller to the return to their previous intensity. Fdloipw Dn IPpo sswitiotcnh. 2 on the 2. Press and hold switch SW1 on the LUT-ELI-3PH unit. 2. Disconnect any occupancy sensors wired to the You should see the following: RadioTouch Controller. • TEST LED (orange) will turn ON. 3. Make the following connections. • All lights controlled by Emergency RadioTouch From LUT-ELI-3PH Unit To RadioTouch Controller controller will go to FULL INTENSITY (factory set). Terminal 8 (+V Input) Terminal 4 (24 V ), Unit A only Note: PHASE ON/OFF status indicator (green) will not turn OFF as test #2 does not create a phase Terminal 7 Terminal 6 (Cir Com) failure. (Circuit Common) • Upon releasing switch SW1, all lights will return to Terminal 1 (Signal) Terminal 2 (Occ Sig) their previous intensities. Note: Only one RadioTouch unit can have its 24 V (number 4) terminal connected to terminal 8 (+V Input) on the LUT-ELI unit regardless of the number of wired RadioTouch units. Available power from this unit Additional RadioTouch Controller for Backup/ for daylight sensors must be Emergency Light(s) derated to 15 mA. LUT-ELI-3PH Unit RadioTouch Unit A RadioTouch Unit B 120/277 V 120/277 V pEfeomewde erbgraecnkcuyp / R wMUC RCS OoSwNEeOToAxTwGNpiA,cT L.eFColIurANI-asGtGrnGbRoUauEnSTdRr.SaXagcoAo, CmP-uAIFO c1N-8hE0SP3ST1dW16MC- -U8R8S80A80-253253Si-T29A94T1606 oidRrCRnePeoeéfnfotRnfesaérsOreimrlu eit1gGrloadt n26e ac tei 0 uihnlóAam es/nG 2 t GeM rIm7unLIununis7ctaIdáísSdtatx easi V o.Td. d l ldne CéEe ’sert i Dsoan .Itn a isn lGsl 2télt atu.s64adl .ildlEa03ate qdC.iHo o.fnozr rep1 smo0 pu0oar eHrpa lr u/1s 0d0®e% fEpeomewde erbgraecnkcuyp / RwUMCRSOoSwNEeOToaAxTwGNpiA,cT Ld.eFColIurANI-asGtiGrnGboRoUauEnSTdRr.SXagcoAo, CmP-uAIFO c1N-8hE0SP3ST1W16MC- -U8R8S80A80-253253S-T29A94T1606 RdrCinePeoeéfnfotRnfesaérsOreimrlu eit1gGrloadt n26e ac tie 0uihnlóAam es/nG 2 t GeM rIm7unLIununis7ctaIdáísdStatx easi V o.Td. d l ldne CéEe ’sert i Dsoan .Itn a isn lGsl 2télt atu.s64adl .ildlEa03ate qdC.iHo o.fnozr rep1 smo0 pu0oar eHrpa lr u/1s 0d0®e% 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 F Slwipi tDchip 2 to ® 0V-10 FSlwipi tDchip 2 to ® 0V-10 the down the down position Power Wiring Cableado de Poder Câblage d'alimentation position Power Wiring Cableado de Poder Câblage d'alimentation GND 12 121 10 0C9LASS8 2 LOW7 VOLT6AGE W5IRING4 3 2 1 S1 1 R2TA-3R X-4F-1SC5 OW2BRGl27reurha7edintP/ e&/eBVgRn/BloeB/ol/uVajlwA3o/acAen/nkzrReacu/dorRolreau/o/nBgVj4joSaleae&d nrOtNotcaR/eOtgurao51Bsn/2RglaC0eocP uVLk*g/rAN6eoSe&gNSroro ai/2rN7 moLiOrSwWHDit8oc imVhtDP P/eVmOadives LnoHdt/enT orCH9itAleb/h oIdanGatu/rteuAegtEirté 1ore DduWn0npeui1st Iao PRtdDrr aoIV1iNibrs2ni1 vVGutoeirNv/cliCobe13i/oGóuCu2utrnrotroaiuulon/rNnatn dneC/tu To1Ttimreao3rm/rNaius/eTtéu1ée tr*4re 15Bu1r6n-In 1RTA2-R X3-F-4SC15OWRB2RGl7reurha7edint/ e2&/eBVgRn/BleBP/ol/uVajlAo/aocAen/nkzrRawc3u/dorRoleau/eo/nBgVjoraleae&d nrO4NoStcR/eOtgarao1tBn/u2Rgla05eosc uVk*Cg/PNeLe&rAgN6orSogi/SrNr oa2i7r SmLwOHDitocWimhtPD/8eVm adVives noHOdt/en orCHLitleb/h oTIdana9tuA/rteuAegtGirté oreDduEnpeu1i st Wao 0PtdDr1r aoIViRibrsni vVIu1toeNirN2v/1cliCoGbei/oGóuCuutrnr1o3troaiu2ulon/rNnatn dneC/tu ToTtimreaorm1m/rNa3ius/eTtéuée tr*re1e4 15Bu1r6n-In (8) (7) (1) *dDECFleloi m Aruba trmta1eae(l2nlnea0utdu2s a aTtVH dcd~aoiemt ró u )igVinsr eéafHio vd(bdiro-a loL aut4eiutcsos mekên p t eowrEae n)crFi larouDye -t sB,wi1 le( ic0soirta é hE6uEp CtscL irelOouiezu-t-dar1lse)o.d0e mnFor Eio eHeúCrnsi n-O2t iLd c 7audeav7me meL VcLuee~ u tnlFret otDru eonHBs n.cie-.os Lrneue rmldiae sews sFoireDrer BE,ie -csoa e-dpr1e ibe0 bslaEa oclCaukOs .at-osvsercies dimming P /bNa 5ll0a0s-t1s0. 634 *dDECFleloi m Aruba trmta1eael2nlnea(0utdus a aTtV2H dcd~aoiemt ró u igVinsr) eéafHio vdbdiro-a loL auteiutcsos mekên p t eowrEae ncrFi larouDye -t sB,wi1 le ic0soirta( é hEuEp CtscL 6irelOouiezu-t-dar1lseo.d0e mnFo)r Eio eHeúCrnsi n-O2t iLd c 7audeav7me meL VcLuee~ u tnlFret otDru eonHBs n.cie-.os Lrneue rmldiae sews sFoireDrer BE,ie -cssoa e-dpr1e ibe0 bslaEa oclCaukOs .at-osvsercies dimmingP /bNa 5ll0a0s-t1s0. 634 (2) Signal To additional (6) Circuit Common cRoandtirooTlloeursch (100 maximum) LUT-ELI-3PH Installation Guide Lutron® | 3 DMS MERUNAXSINE +C2O4MVMFWON ´CFOACNPT´A NC/TCS ´CFOACNPT´A NC/TOS NRAODTI OUTSOEDUCH PH F TAECSETF LED123 PELV (Class 2: USA) OOc 1cc5.c CV Soimg C2iPr4 SC V o _S+mig CCCOC COo m12354 P/N 500-10634 © 2006 Lutron Electronics Co., Inc. PELV (Class 2: USA) OOc 1cc5.c CV Soimg C2iPr4 SC V o _S+mig CCCOC COo m43512 P/N 500-10634 © 2006 Lutron Electronics Co., Inc. Emergency Lighting Interface LUT-ELI-3PH | Installation Guide Installing a LUT-ELI-3PH Unit in a Panel-Based System Line Voltage Connections WARNING! Danger of shock. May result Note: Provide proper short-circuit and overcurrent in serious injury or death. DO NOT WIRE protection at the distribution panel. Maximum circuit WHEN LIVE! Switch off power to all power breaker rating of 20 A. feeds via circuit breaker or isolator before wiring or servicing the LUT-ELI-3PH unit and Panel-Based System. Buttons and LEDs in the unit are used for troubleshooting. If wiring is exposed when accessing buttons and LEDs, the unit must be accessed by a certifed electrician, following local codes. GP3 panel shown Wiring from Normal (Non-Essential) GP Panel Control wiring to Typical load circuit circuit selector DH1 SH1 H1 DH2 SH2 H2 DH3 SH3 H3 N Red Branch GND 12 1 10 C9LAS8 2 LOW7 VOLT6AGE W5IRING4 3 2 1 S1 Red cbirrecaukite rs White Green (to ground lug) Terminal blocks N bleouctkral Nfeoerdm wailr pinogwer Ground lug Wiring from Mains with GP, LP, XP, and XPS/LCP Panels Ground Neutral Phase C Phase B Phase A Normal Power Lutron® | 4 LUT-ELI-3PH Installation Guide ´SDCM+MF2EROAOU4NCANMXVSIPTNMFE´A WNOC/NTCS PH F TAECS´CNRFETFAOAODCNTI PTOUL´A ETSNCDOE/TO312DUSCH Red Red Red White Green Normal to panel Emergency Lighting Interface LUT-ELI-3PH | Installation Guide Installing a LUT-ELI-3PH Unit in a Panel-Based System (continued) NEC® Class 2/PELV: USA Connections Notes Wiring Notes • Pull NEC Class 2/PELV wiring for system • NEC Class 2/PELV wiring link is 500 to 2000 feet communications. (152 to 610 m), use Lutron® cable GRX-CBL-46L: • NEC Class 2/PELV wiring must be daisy-chained. - Two 12 AWG (2.5 mm2) for control wiring • NEC Class 2/PELV wiring must be run separately from (+V and com) line (mains) voltage. - O ne twisted, shielded pair 22 AWG (0.5 mm2) • A LUT-ELI-3PH unit can be placed anywhere on the for data link power panel link. - One 18 AWG (1.0 mm2) for sense line between panels. • Lutron has also approved smaller-gauge cable from Belden®, Liberty Wire & Cable®, AlphaWire Company, and Signature Wire Corp. Ask for Lutron GRAFIK Eye® Cable. Processor panel Dimming panel LUT-ELI-3PH Unit Power panel link Wallstation links Panel to panel wiring See above for wiring notes LUT-ELI-3PH Installation Guide Lutron® | 5 Emergency Lighting Interface LUT-ELI-3PH | Installation Guide I n s t a l l i n g a L U T - E L I - 3 P H U n i t i n a P a n e l( -c Bo an st ie nd u eS dy ) s t e m N ® E CC l Pa as ns e l 2 / t Po E PL aV n e l W i r i n g N o t e s • E m e r g e n c 2) y •w PEaci ho NErCw Cleasse 2 /PErLV te:rmina l canT accehpt onely a d d i t i o n a l 1 8 A W G ( 1 . 0 m m i s a “ s e n s e ” twol 18 Ai WGn (1.0 mem2) w ires.f Twor 12 AoWG m t e r m i n a l 1 2 o n t h e L U T - E L I - 3 P H . T h i s s e n s e l i n e a l (2.5l mmo2) conwductosrs wo n't fta. Connect a s shoEwn m e r g e n c y ( E s s e n t i a l ) l i g h t i n g p a n e l t o “ s e n s e ” w h e n b elowN in wiroing exrampmle B. a l ( N o n - E s s e n t i a l ) p o w e r i s l o s t . I f m o r e t h a n o n e e m e Cr onngectioens n c y l i g h t i n g p a n e l n e e d s t o s e n s e N o r m a l ( N o n - E s s e n t i a l ) f r o m a s p e c i f c L U T - E L I - 3 P H u n i t , y o u m a y h a v e t o r u n a LU T-ELdI-3PHe d Ciircuitc Seleactor t e d w i r e b e t w e e n e a c h L U T - E L I - 3 P H u n i t a n d E m e r Termginal 1e2 (Sennse) c Termy inal 5 (Se(nse) E s s e n t i a l ) p a n e l ( s ) . • S Ch oi s ne h nl a i sdese h /bc l oDte id wwrlni i naon r iwg i n n : g example A: Terminal 11 (Drain) Terminal D (Drain) - D o not connect to Ground (Earth) or circuit selector. Terminal 10 (MUX) Terminal 4 (MUX) - C onnect the bare drain wires and cut off the outside Terminal 9 (MUX) Terminal 3 (MUX) shield. Terminal 8 (+V Input) Terminal 2 (+24VFW) Wiring Example A Terminal 7 Terminal 1 D La it na(Circk uit C:ommon) (Common) C o n t r o ( l s 1 h ) i e l d e d , W i r i n g t : w p i a s iSt r ee nd s e : ( ( 1 C1m2:A 2o2) ). m Wm 5 SDGm hr o ai (31 nMeAim18: 2n lU)W . m dX0G /(5 S1m1:A 2e8) l ). m Wni 0 Gns ee 1 2 2 :V 4 4 M : U X 1 2 T l o i c g o h n t t i rn og l s 3,4 2 o p r r o c e s s o r s 3,4 5 1 2 3 4 D 5 1 2 3 4 D 5 DataAOK Power Data B OK DataAOK Power Data B OK Link Link Link Link 1 2 3 4 D 5 A B C D 1 2 3 4 D 5 A B C D GND SELECT CIRCUIT SELECT CIRCUIT 12 1211 10 0C9LASS8 2 LOW7 VOLT6AGE W5IRING4 3 2 1 S1 1 1 2 2 Circuit Circuit Panel 1 Panel 2 Wiring Example B (4) 12 AWG (2.5 mm2) 1 2 3 4 D 5 Data A OK Power OK Data B OK Lutron® | 6 LUT-ELI-3PH Installation Guide Link Link 1 2 3 4 D 5 A B C D SELECT CIRCUIT 1 2 Circuit VIEW VALUE SELECT VALUE M ´CSDM+CF2EROAU4NCANMXVSIPTNMFE´AW ONCN/TCS PH F TAECS´NRCFETFAOADCNTI PTOUL´A ETSNCDOE/T231ODUSCH Common +24VFW MUX MUX Drain Sense Common MUX Common MUX Drain 24VFW MUX MUX Drain Common Sense +24VFW MUX MUX Drain Sense Comm MUX Common MUX MUX Drain MUX Drain Emergency Lighting Interface LUT-ELI-3PH | Installation Guide Installing a LUT-ELI-3PH Unit in a Panel-Based System (continued) Setting the Circuit Selector Normal/Emergency Circuit Selector in Normal Circuit Selector in Switch (SW6) Position (Non-Emergency) Panel Emergency (Essential) Panel Panels are shipped with SW6 (located at the base of each Circuit Selector) in the middle position. Terminal 5 (sense) 1 2 3 4 D 5 1 2 3 4 D 5 has no affect on the circuit selector operation. Data A OK Power OK Data B OK Data A OK Power OK Data B OK All Emergency Panels • Move SW6 to the right Emergency (Essential) position. In Link Link Link Link this arrangement, the LUT-ELI-3PH unit will be the only unit 1 2 3 4 D 5 A B C D 1 2 3 4 D 5 A B C D controlling the sense line. If one or more phases go down, SELECT CIRCUIT SELECT CIRCUIT 1 1 the LUT-ELI-3PH unit sends a signal through the sense 2 2 line to Emergency (Essential) panel(s). The lights controlled Cir cuit Cir cuit by these panels will go to ‘ord’ override levels (factory set VIEW VALUE VIEW VALUE to full intensity). When normal power is restored, lights will SELECT VALUE SELECT VALUE return to their previous intensities. Link A 3 Link A 3 Note: When in ‘ord’ override mode (factory set to full Link B 4 Link B 4 intensity), ‘ord’ will appear on value display to confrm that Value Value Emergency (Essential) position is in effect. SCiErcLuEiCt TLeVvAeLlUE DISPLA YED 5 SCiErcLuEiCt TLeVvAeLlUE DISPLA YED 5 Load Type (See Instructions) Load Type (See Instructions) Test the System Zone Assignment w/ CZoirnceu iCt SapchtuerdeuTMle Zone Assignment w/ CZoirnceu iCt SapchtuerdeuTMle Please perform the following tests to ensure proper Low-End Trim Low-End Trim installation. High-End Trim High-End Trim Address ('Ad' displayed) Address ('Ad' displayed) 1. Turn off one of the Normal (Non-Essential) phase(s) Warning - Read instructions to set the Load Warning - Read instructions to set the Load breaker(s) that the LUT-ELI-3PH unit is monitoring. Type. Instructions show more load types. Type. Instructions show more load types. Load Type Quick Reference: Load Type Quick Reference: You should see the following: 1---1 IUnncasnsdiegsnceednt 34-1 Neoonn-D /i mCC 1---1 IUnncasnsdiegsnceednt 34-1 Neoonn-D /i mCC • PHASE ON/OFF status Indicator (green) will turn OFF as 2-1 Fluorescent Lutron Hi-lume R FDB Ballast 2-1 Fluorescent Lutron Hi-lume R FDB Ballast the above test creates a phase failure. 2-2 Fluorescent Lutron Tu-WireTM Ballast 2-2 Fluorescent Lutron Tu-WireTM Ballast • Circuit selector on Emergency (Essential) panel will go to ‘ord’ override mode. • All lights controlled by Emergency (Essential) panel will go to Full Intensity (Factory Set). • The circuit selector in Emergency (Essential) panel will read ‘ord’ on the value display when in Emergency mode. • fArell elizgeh tast cthoenitrr orellsepde bcyti vNeo irnmteanl s(Nitieosn.-Essential) panel will LINK 1 LINK 2 (Non-NEosrsm) al Em(Eesrsgeenntciayl) LINK 1 LINK 2 (Non-NEosrsm) al Em(Eesrsgeenntciayl) 2. Press and hold switch SW1 on the LUT-ELI-3PH unit. Switch is Switch is in center moved to You should see the following: position the right • TEST LED (orange) will turn ON. (emergency) Note: PHASE ON/OFF status indicator (green) will not turn position OFF as test #2 does not create a phase failure. • Circuit Selector on Emergency (Essential) Panel will go to ‘ord’ override mode. • All lights controlled by Emergency (Essential) panel will go to FULL INTENSITY (factory set). • The circuit selector on Emergency (Essential) panel will read ‘ord’ on the value display when in Emergency Mode. • All lights controlled by Normal (Non-essential) panel will freeze at their current intensities. • Upon releasing switch SW1, all lights will return to their original intensities. LUT-ELI-3PH Installation Guide Lutron® | 7 Common 24VFW MUX MUX Drain Sense Comm MUX MUX Drain Common 24VFW MUX MUX Drain Sense Comm MUX MUX Drain Emergency Lighting Interface LUT-ELI-3PH | Installation Guide Installing a LUT-ELI-3PH Unit in an EcoSystem® or Quantum® System Line Voltage and NEC® Class 2/PELV Connections WARNING! Danger of shock. May result in Note: Provide proper short-circuit and overcurrent serious injury or death. DO NOT WIRE WHEN protection at the distribution panel. Maximum circuit LIVE! Switch off power to all power feeds breaker installation of 20 A. via circuit breaker or isolator before wiring or A Lutron® PP-120H or PP-277H power pack must be s ligehrvtincgin gc othnetr oLlU sTy-sEteLmI-3 oPrH Q uunaint taunmd sEycsotSemys.tem used to power the LUT-ELI-3PH unit when used with a bus supply. Both the power pack and the bus supplies Buttons and LEDs in the unit are used for must be fed from a normal/emergency supply. troubleshooting. If wiring is exposed when accessing buttons and LEDs, the unit must be accessed by a certifed electrician, following local codes. Wiring to EcoSystem Bus Supply 24 V *PP-120H or PP-277H (Red) 1 5 3-0p0/6h-0a3s 4He7 z V (CBolamcmk)on pPaocwke*r Hot normal supply See Figure #1 or Figure #2 From 120 or 277 V on page 2 of Neutral Normal/Emergency this guide. supply GND 12 11 10 C9LASS8 2 LOW7 VOLT6AGE W5IRING4 3 2 1 S1 (8) (7) (1) Common (pin 5) Common Bus supply Bus supply 24 V Emerg. signal (pin 6) 100-277 V Normal/ C buosn nseucptp ulieps to 32 Esumpeprlgyency Wiring to Quantum systems *PP-120H or PP-277H 24 V F Nrorm a1l2/E0m oerr 2g7en7c Vy supply H Noeut tral Ppaocwke*r (C(BRoelamdc)km)on 100-277 V Normal/Emergency supply Common E1 E2 E1 E2 EM C GND 12 11 10 C9LASS8 2 LOW7 VOLT6AGE W5IRING4 3 2 1 S1 (8) (7) (1) Emerg. Connect up to 8 signal Quantum hubs Lutron® | 8 LUT-ELI-3PH Installation Guide 1 2 3 4 5 6 7 8 CDCM+´SMF2EROAU4NACNMXVSIPTNMFE´AW ONCN/TCS CN´ RFAOADCNTI PTOU´A TSNCOE/TODUSCH PH F TAECSETF LED321 M CDS+´ CF2EROAOU4NCANMXVSIPTNMFE´A WNOC/NTCS PHF TAECS´RNCFETFAOAODCNTI PTOUL´A ETSNCDOE/TO213DUSCH Emergency Lighting Interface LUT-ELI-3PH | Installation Guide Installing a LUT-ELI-3PH Unit in a GRAFIK Eye® QS Unit NEC® Class 2/PELV Connections WARNING! Danger of shock. May result in Notes serious injury or death. DO NOT WIRE WHEN • Provide proper short-circuit and overcurrent LIVE! Switch off power to all power feeds protection at the distribution panel. Maximum via circuit breaker or isolator before wiring or circuit breaker installation of 20 A. servicing the LUT-ELI-3PH unit and GRAFIK Eye QS unit. • When normal power loss is detected at the LUT-ELI-3PH unit, all zones in the GRAFIK Eye QS Buttons and LEDs in the unit are used for troubleshooting. If wiring is exposed when units will go to their emergency states. accessing buttons and LEDs, the unit must be • The GRAFIK Eye QS unit MUST be powered from a accessed by a certifed electrician, following normal/emergency power feed. local codes. Wiring to a GRAFIK Eye QS Control Unit Note: For 1-phase 2-wire application, connect phase A, B, and C wires on LUT-ELI-3PH together for phase sensing. 100-347 V 50/60 Hz 3-phase Normal supply See Figure #1 or Figure #2 on page 2 of this guide. GRAFIK Eye QS unit QSGRJ model (back view) GND 12 9 8 7 T6AGEA W5IRINGG4 E 3 2W 1I R I N GS1 (3) 18 AWG (8) (7) (1) +24 V Signal CCI SIG 24 V Common CCI Com Normal/Emergency 20 A 120 V 1-Phase 2-Wire power feed (3) 12 AWG (2.5 mm²) 120-127 V or 220-240 V distribution panel LUT-ELI-3PH Installation Guide Lutron® | 9 SENSE SENSEN S DRAIN MUX MUX C´FOACNPFTO´A NC/PTOASN ´ CT PAN ´ C/ TO S +24VFW RNRAODTI OUATSTOE DUDSCDHU I C C ´FOACMPM´ ONN/C PHFTAECSETF LED132E D CONTACTS ´FACP´ N/O CONTACTS NOT USED RADIOTOUCH LED3 12 11 10 9 8 7 6 5 4 3 2 1 CLASS 2 LOW VOLTAGE WIRING Emergency Lighting Interface LUT-ELI-3PH | Installation Guide Installing a LUT-ELI-3PH Unit with an Notes: Provide proper short-circuit and overcurrent Energi Savr NodeTM Unit(s) protection at the distribution panel. Maximum circuit breaker installation of 20 A. NEC® Class 2/PELV Connections • A Lutron® PP-120H or PP-277H power pack must be WARNING! Danger of shock. May result used to power the LUT-ELI-3PH unit when used with an in serious injury or death. DO NOT WIRE Energi Savr Node unit(s). Both the power pack and the WHEN LIVE! Switch off power to all power Energi Savr Node unit(s) must be fed from a normal/ feeds via circuit breaker or isolator before emergency supply. wiring or servicing the LUT-ELI-3PH and • - Energi Savr Node unit. PH unit, all zones in the Energi Savr Node unit will go to Buttons and LEDs in the unit are used for their emergency states. troubleshooting. If wiring is exposed when accessing • Energi Savr Node unit MUST be powered from a buttons and LEDs, the unit must be accessed by a normal/emergency power feed. certifed electrician, following local codes. Connections Wiring from Energi Savr Node Units LUT-ELI-3PH Energi Savr Node Unit Power Pack Note: For 1-phase 2-wire application, connect Terminal 8 (+V Input) ------------------------- Red Wire phase A, B, and C wires on LUT-ELI-3PH together Terminal 7 Com Black Wire for phase sensing. (Ci Wrcuhite Cn onmomrmoanl) pow(eErm loesrgse insc dy eCteCcI tInepdu at)t the LUT-ELI-3 Terminal 1 (Signal) Emerg (Emergency CCI Input) --------------- 100-347 V 50/60 Hz The 3-phase Normal supply See Figure #1 or Figure #2 on page 2 of this guide. 2 #12 PP-120H or Input Power PP-277H (120 or 277 V ) *+24 V (Red) Normal/Emergency Power *Common (Black) GND 12 11 10 C9LASS8 2 LOW7 VOLT6AGE W5IRING4 3 2 1 S1 (8) (7) (1) *Signal *Common *NEC Class 2/PELV Wiring 18 AWG (1.0 mm²) Note: *Signal Up to 32 QSN-4T16-S or QSN-4S16-S units can be *Common connected to 1 LUT-ELI-3PH Lutron® | 10 LUT-ELI-3PH Installation Guide MSDMERUNAXSINE +C2O4MVMFWON ´CFOACNPT´A NC/TCS ´CFOACNPT´A NC/TOS NRAODTI OUTSOEDUCH PH F TAECSETF LED231