≠ EDICT ± OF GOVERNMENT In order to promote public education and public safety, equal justice for all, a better informed citizenry, the rule of law, world trade and world peace, this legal document is hereby made available on a noncommercial basis, as it is the right of all humans to know and speak the laws that govern them. EAS 260 (2007) (English): Zippers — Glossary of terms EAS 260:2007 ICS 59.080.30 HS 9607.00.00 EAST AFRICAN STANDARD Zippers — Glossary of terms EAST AFRICAN COMMUNITY © EAC 2007 First Edition 2007 EAS 260:2007 Foreword Development of the East African Standards has been necessitated by the need for harmonizing requirements governing quality of products and services in East Africa. It is envisaged that through harmonized standardization, trade barriers which are encountered when goods and services are exchanged within the Community will be removed. In order to achieve this objective, the Partner States in the Community through their National Bureaux of Standards, have established an East African Standards Committee. The Committee is composed of representatives of the National Standards Bodies in Partner States, together with the representatives from the private sectors and consumer organizations. Draft East African Standards are circulated to stakeholders through the National Standards Bodies in the Partner States. The comments received are discussed and incorporated before finalization of standards, in accordance with the procedures of the Community. East African Standards are subject to review, to keep pace with technological advances. Users of the East African Standards are therefore expected to ensure that they always have the latest versions of the standards they are implementing. © East African Community 2007 — All rights reserved* East African Community P O Box 1096 Arusha Tanzania Tel: 255 27 2504253/8 Fax: 255-27-2504481/2504255 E-Mail: [email protected] Web: www.each.int * © 2007 EAC — All rights of exploitation in any form and by any means reserved worldwide for EAC Partner States’ NSBs. ii © EAC 2007 — All rights reserved EAST AFRICAN STANDARD EAS 260:2007 Zippers — Glossary of terms 1 Scope This East African Standard covers terms or meanings used in the zipper industry. 2 Definitions For the purpose of this East African Standard the following definitions shall apply: B bail or lug A portion or portions of the slider to which the pull or pulls are attached. bead a) Separate element zipper — An enlarged section on inner edge of each tape to which scoops are affixed. b) Continuous-monofilament zipper — An enlarged section of the tape located at the outer edge of the continuous interlocking elements and against which the slider flanges bear. The bead is optional on continuous-monofilament zippers. C cam — A portion or portions on the pull that extend through a window or windows to effect a locking action in cam-lock sliders. chain — The assemblages formed by interlocking several elements of two stringers. chain thickness — The measurement from front to back of the chain. chain width — The distance between the shoulders of the interlocked elements or between the outermost edges of thee bead if the bead extends beyond the elements (see Figure 1). connecting ring — A device used to secure special pull to bail or lug. cord — A strand of multiple yarns for use in forming a bead. crimp — As applied to a continuous-monofilament zipper, the predetermined formation of the monofilament cross-section at the point where the continuous-monofilament element is interlocked. cut-off — The measurement of a scoop from the head side to the pocket side of the legs. D diamond — A wedge-shaped portion of slider between the throats. E elements interlockable a) General — Formed devices affixed along the edge of a pair of tapes, which are interlocked or disengaged by the movement of the slider. © EAC 2007 — All rights reserved 1 EAS 260:2007 Figure 1 — Slide fasteners: Dimensions b) Continuous — Continuous-formed-monofilament designed for interlocking and affixed along the edge o a tape. c) Scoops — Separately formed elements designed for interlocking and affixed along the edge of the tape (see Figure 2). NOTE scoops are of many designs but the nomenclature is generally the same for all types. NOTE Scoops are of many designs but the nomenclature is generally the same for all types Figure 2 — Scoop 2 © EAC 2007 — All rights reserved EAS 260:2007 F fastener, closed-end — A slide fastener which does not permit the complete separation of the two stringers. Normally the top end of the fastener separates as the slider is lowered, although there is an additional type where the top end are permanently joined together by means of a bridge stop (see Figures 3(a) and 3(b)). Figure 3 — Closed-end fasteners fastener, concealed — A slide fastener with the tapes folded so that on closure neither the slider body nor the fastener are visible from the outside of the article. fastener, length of — The distance from the top of the slider to the bottom stop, or box in the case of an open-end fastener, measured with the slider in the top position and with the puller in the downward position (see Figure 1). fastener, open-end — A slide fastener having a special fitment at the bottom end of each stringer in place of the bottom stop, so designed as to permit the two stringers to be completely separated and re-assembled at will when the slider is in the full open position. The special fitment normally consists of a pin permanently fixed to the bottom end of one stinger which fits into a box permanently fixed to the bottom end of the other stringer. fastener, slide — A fastening device consisting of two flexible, interlocking stringers with or without end stops and a slider so arranged that by moving the slider along the stringers in one direction an opening is formed, and by moving it in the other, the opening is closed. The end which is adjacent to the slider when the device is fully open is designated the bottom end. The other end is designated the top end. fastener, two-way — A slide fastener fitted with two sliders that operate with equal facility in either direction. This type is available in a variety of forms which are illustrated in Figure 4. fasteners, batch of — A quantity of fasteners having one design, one performance code and one size. flanges — The edges of the slider formed to contain the chain. © EAC 2007 — All rights reserved 3 EAS 260:2007 Figure 4 — Two-way fasteners H head or heads — The portion of a scoop that engages the pocket. K knuckle — See crimp. L legs — The two portions of a portion of a scoop that affix the scoop to the head. locking device — A device incorporated in the slider unit restricting its free movement along the fastener length in on opening direction. The locking device may operate either automatically on release of the puller or by manual pressure on the puller. M mouth — The opening in a slider that receives the chain. mouth width — The distance between the slider flanges at the point where they bear against the shoulders of the interlocked elements or at the outermost edges of the bead if the bead extends beyond the elements. P pin, locking — The projection on a pull that fits between adjacent scoops of a fastener when a pin- lock slider is in the locked is in the locked position. 4 © EAC 2007 — All rights reserved EAS 260:2007 pin, retainer — A tube-like element, similar to the separable pin, attached over the head at the bottom end of the stringer opposite to the separable pin. This element is designed to hold the fixed retainer in position. pin-separable — A tube-like element attached over the bead at the bottom end of one stringer. Pocket — The cavity of a scoop designed to receive the head. pull (or puller) — The fitting attached to the slider to facilitate manipulation. R retainer, fixed — An element permanently attached onto the retainer pin at the bottom of one stringer. It has an opening shaped to fit the separable pin. In order to close, the separable pin is passed through the slider body and then inserted into this opening. Thus, the fixed retainer holds or retains the two stringers in alignment for interlocking. retainer, movable — A movable or sliding element performing a similar function to that of the fixed retainer, the purpose being to permit separation of the two stringers from the bottom, without the necessity of opening the zipper from the top. This element is not removable from the bottom (see Figure 5). Figure 5 — Movable retainer scoops — See interlocking elements. shoulder — The bearing surface of an interlocking element by which the chain is contained inside the flanges of the slider. slider — The part that opens the zipper when moved in one direction and closes it when moved in the opposite direction. The slider can have single or double pull (or puller) (see Figure 6). Figure 6 — Sliders © EAC 2007 — All rights reserved 5 EAS 260:2007 slider, automatic lock — A slider that provides automatic, positive locking action on the chain when the pull is released. slider, flange lock — A slider with notches in the flanges of the slider that block the shoulders of the scoops when the stringers are pulled apart. stops — The elements at tops and bottom of chain or stringer that prevent the slider from leaving the chain. stop, releasing — An element attached at or near the top of the stringer on the separable pin side. This element limits the travel of the slider at the open end of the chain under normal closing operations. The slider may be forced beyond it when added force is exerted towards the top of the zipper. Releasing stops are used on zippers of the ‘quick release’ or ‘quick’ disassembly’ type (commonly referred to as ‘QR’ or as ‘QD’ zippers) (see figure 7). Figure 7 — Releasing stops stop, bottom — A part affixed to both stringers immediately below or over, the chain, holding the two stringers together at the bottom and preventing the slider from leaving the chain (see Figure 8). Figure 8 — Bottom stop stop, bridge stop — A part affixed immediately above the chain, holding the tops of two stringers together and preventing the slider from leaving the chain (see figure 9). 6 © EAC 2007 — All rights reserved