Installation Operation Care • • Applause Honeycomb Shades ® Cordlock Operating System Contents GETTING STARTED Product View ..........................................................................1 Tools and Fasteners Needed .................................................2 INSTALLATION Installation Overview .............................................................3 Mount the Installation Brackets — Inside Mount ................4 Mount the Installation Brackets — Outside Mount .............5 Mount the Installation Brackets — End Mount ....................7 Install the Shade ....................................................................8 Attach Hold-Down Brackets (Optional) .................................8 OPERATION Operate the Shade .................................................................9 Troubleshooting ...................................................................10 CARE Removing the Shade (If Necessary) ....................................13 Cleaning Procedures ............................................................13 CHILD SAFETY Warning ...............................................................................15 Questions? Call the Hunter Douglas Customer Information Center at 1-888-501-8364. © 2016 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or their respective owners. Getting Started PRODUCT VIEW Installation Cordlock Brackets Stopball STANDARD BOTTOM-UP SHADE Tassel Cord Breakaway Tassel Cord Stop TOP-DOWN/ BOTTOM-UP SHADE Not Shown: Top-Down, Duolite™, and Two-On-One Headrail Shades 1 Getting Started Thank you for purchasing Hunter Douglas Applause® honeycomb shades. With proper installation, operation, and care, your new shades will provide years of beauty and performance. Please thoroughly review this instruction booklet and the enclosed packing list before beginning the installation. If your shade has a protective plastic cover on the fabric-covered headrail, keep the cover in place until the shade is installed. TOOLS AND FASTENERS NEEDED ■ Flat blade and Phillips screwdrivers ■ Level (laser level is recommended) ■ Measuring tape and pencil ■ Power drill, 3/32" drill bit, and 1/4" hex driver In addition, you will need fasteners designed to work with your specific mounting surface(s). ■ #6 Hex Head Screws (Provided). Two 11/2" screws are provided per installation bracket. ■ Longer #6 Hex Head Screws (Not Provided). If using spacer blocks, use #6 screws long enough for a secure attachment. ■ Speed Nuts and Screws (Provided). Extension brackets come with speed nuts and screws. ■ Drywall Anchors (Not Provided). Use drywall anchors when mounting into drywall. Speed Nut #6 x 11/2" Longer #6 Hex Head Screw and Screw Hex Head Screw for Use with Spacer Blocks (Provided with Each (Provided) (Not Provided) Extension Bracket) 2 Installation INSTALLATION OVERVIEW ■ Your order will include installation brackets specific to the pleat size and mounting style of your shades. 3/8" 3/4" 3/8" 3/4" Standard Standard Swivel Swivel 3/8" 3/4" Installation Installation Bracket Bracket End Mount End Mount Bracket Bracket (Optional) (Optional) Bracket Bracket ■ The number of installation brackets required varies with Shade Brackets headrail width, as shown in the table. Width Required 12" – 31" 2 Mounting Types and Window Terminology 311/8" – 79" 3 If the installation brackets are mounted correctly, the rest 791/8" – 96" 4 of the installation process follows easily. To prepare for this 961/8" – 139" 5 important first step, review the mounting types and basic 1391/8" – 174" 6 window terminology illustrated below. Molding Head Jamb Jamb Jamb Collectively, the sill and Outside Mount jambs are called the Inside Mount Shade mounts “window casement.” Shade fits within outside window opening. window opening. Sill ■ Refer to the appropriate page below based on your order: ➤ Inside Mount — Page 4 ➤ Outside Mount — Page 5 ➤ End Mount — Page 7 3 Installation MOUNT THE INSTALLATION BRACKETS — INSIDE MOUNT ■ Mark 3" from each jamb. ➤ If more than two installation brackets came with your order, space additional bracket(s) evenly between the two end brackets and mark their location. Mount into wood whenever possible. 3" Space Evenly Space Evenly 3" Jamb Jamb ■ Center the brackets on your marks and mark the Depth Chart For Bracket Placement location of the screw holes. Bracket Fully ➤ Mounting depth will vary depending on the Type Minimum Recessed fabric pleat size. Refer to the chart for depth 3/8" Standard 1" 15/8" requirements. 3/4" Standard* 11/4" 23/8" ➤ For fully recessed mounting, the entire 3/8" Swivel 1/2" 11/4" shade is inside the window casement. 3/4" Swivel* 1/2" 2" IMPORTANT: The front edges of the *Double and triple honeycomb fabrics use 3/4" brackets. installation brackets must be level and aligned. 3" 3" Standard Swivel Bracket Bracket See Chart See Chart for Depth for Depth ■ Drill the screw holes using a 3/32" drill bit. CAUTION: Use drywall anchors when mounting into drywall. ■ Attach the installation brackets using the screws provided. ➤ Check that the mounting surface is level and the brackets are aligned. If mounting to a heavily textured surface, shim the brackets, if needed. Standard Swivel Bracket Bracket Proceed to “Install the Shade” on page 8. 4 Installation MOUNT THE INSTALLATION BRACKETS — OUTSIDE MOUNT ■ Center the headrail over the window opening at the desired height. Use a pencil to lightly mark each end of the headrail. ➤ Alternatively, measure the width of the headrail and use that width to mark the headrail end points over the window opening. ■ Mark 3" from each end of the headrail. ➤ If more than two installation brackets came with your order, space them evenly between the two end brackets and mark their location. Mount into wood whenever possible. Headrail End Marks 3" Space Evenly Space Evenly 3" Window Opening ■ Center the brackets on your marks, then mark each of the screw holes. ➤ A minimum flat vertical surface of 5/8" for a 3/8" bracket or 1" for a 3/4" bracket is required to mount the brackets. ➤ The top of the installation brackets or extension brackets should be at the desired shade height. IMPORTANT: The brackets must be level and aligned to each other. CAUTION: The rear of the brackets must be flush against a flat mounting surface. Do not mount brackets on curved molding. Standard Extension Bracket Bracket 5 Installation ■ Drill the screw holes using a 3/32" drill bit. CAUTION: Use drywall anchors when mounting into drywall. ■ Attach the installation brackets or extension brackets using the screws provided. IMPORTANT: The front edges of the brackets must be level and aligned to each other. ■ If using spacer blocks with installation brackets, attach the spacer block(s) and installation bracket to a flat vertical mounting surface with Spacer #6 mounting screws long enough for a secure Blocks installation. CAUTION: The rear spacer block must be flush against a flat mounting surface. Do not mount spacer blocks and installation brackets on curved molding. ➤ Each spacer block projects the installation bracket 1/2" from the mounting surface. A maximum of 11/2" of spacer blocks per installation bracket is recommended. ➤ The solid side of the spacer blocks faces the mounting surface. ■ If using extension brackets, attach an installation bracket Speed Nut to the underside of each extension bracket using the provided screws and speed nuts. Extension Bracket Installation Bracket Proceed to “Install the Shade” on page 8. 6 Installation MOUNT THE INSTALLATION BRACKETS — END MOUNT End mount the headrail when conventional mounting techniques will not work — for example, in an arched window opening. Install End Mount Brackets onto the Headrail ■ On a headrail end without a cordlock, remove the end cap from the headrail. ■ Partially insert the short end of the specialty end mount bracket under the small fabric channels in the headrail. Headrail Specialty End Mount Short Bracket End End Long Small Fabric Channels Cap End ■ Replace the end cap and push the bracket and end cap snugly into the headrail. ■ To install the bracket on the cordlock side(s), pull the shade cord to the center of the shade to release the lock, as if lowering the shade. ■ Pull the cordlock out 1/2" and insert the short end of the specialty end mount bracket under the small fabric channels in the headrail. IMPORTANT: Do not pull the cordlock all the way off the Cordlock headrail. ■ Push the bracket and cordlock snugly back into the headrail. IMPORTANT: For instructions on installing an arch over a rectangular shade, see the Installation, Operation, and Care instructions that came with your arch shade. Install the End Mount Brackets to the Window Jamb ■ Position the fully lowered shade in the window. ■ Gently push the fabric away from the installation bracket to allow access to the screw holes. ■ Mark the screw hole locations. IMPORTANT: Check that the front edges of the shade are level and aligned. ■ Remove the shade with the attached end mount brackets from the window. ■ Drill the screw holes using a 3/32" drill bit. ■ Attach the end mount brackets using the screws provided. Proceed to “Operate the Shade” on page 9. 7 Installation INSTALL THE SHADE Standard Brackets Headrail ■ Position the shade so that the cord faces you. ■ Slip the headrail into the installation brackets so the front of the bracket slides under the front groove on the top of the headrail. ■ Gently roll the back of the headrail up and push back to snap into place. ■ Tighten the tab screw. Tab Screw Optional Swivel Brackets Mounting Holes ■ Place the swivel brackets in the open position. ■ Place the headrail against the back of the swivel brackets. ■ Rotate the swivel arm to snap the locking Bracket tab under the front groove on the top of the in Open Position headrail. ■ The shade is locked when the push tab is against the headrail. Locking Bracket Tab in Locked Position Push Tab ATTACH HOLD-DOWN BRACKETS (OPTIONAL) Hold-down brackets are used on outside mounted shades only. ■ Lower the shade and place the pins from the hold-down brackets into the bottom rail end caps. ■ On the mounting surface, mark the screw holes. ■ Check that the brackets are level and aligned, and attach them using two screws. 8