Errata to ANSI/AWWA C200-12 Standard for Steel Water Pipe, 6 In. (150 mm) and Larger (August 2012) 1. Add footnote 3 callout to Table 1, pg. 11, as follows: ASTM A139/A139M3 2. Change Sec. 4.11.3, page 21, to read: 4.11.3 Straightness. The maximum deviation from a straight line, over the entire pipe length, shall be 0.2 percent of the pipe length. 3. Correct the AWS section numbers in Sec. 5.2.2.1, Items 4 and 5, page 29, as follows: 4. Ultrasonic (UT) in accordance with AWS D1.1, Section 6, Part F, accep- tance criteria in accordance with Part C, 6.13.1; or in accordance with ASME Section V, Article 4, acceptance criteria in accordance with ASME Section VIII, Div. 1, appendix 12; or API 5L, Annex E. 5. Radiographic (RT) in accordance with AWS D1.1, Section 6, Part E, accep- tance criteria in accordance with Part C, 6.12.1; or in accordance with ASME Section V, Article 2, acceptance criteria in accordance with ASME Section VIII, Div. 1, Part UW, UW-51, or UW-52 as applicable; or API 5L, Annex E. ANSI/AWWA C200-12 (Revision of AWWA C200-05) The Authoritative Resource on Safe Water® AWWA Standard Steel Water Pipe, 6 In. (150 mm) and Larger SM Effective date: Sept. 1, 2012. First edition approved by AWWA Board of Directors June 26, 1975. This edition approved June 10, 2012. Approved by American National Standards Institute June 22, 2012. 6666 West Quincy Avenue Advocacy Denver, CO 80235-3098 Communications T 800.926.7337 Conferences www.awwa.org Education and Training Science and Technology Sections Copyright © 2012 American Water Works Association. All Rights Reserved. AWWA Standard This document is an American Water Works Association (AWWA) standard. It is not a specification. AWWA standards describe minimum requirements and do not contain all of the engineering and administrative information normally contained in specifi- cations. The AWWA standards usually contain options that must be evaluated by the user of the standard. Until each optional feature is specified by the user, the product or service is not fully defined. AWWA publication of a standard does not constitute endorsement of any product or product type, nor does AWWA test, certify, or approve any product. The use of AWWA standards is entirely voluntary. This standard does not supersede or take precedence over or displace any applicable law, regulation, or codes of any governmental authority. AWWA standards are intended to represent a consensus of the water supply industry that the product described will provide satisfactory service. When AWWA revises or withdraws this standard, an official notice of action will be placed on the first page of the Official Notice section of Journal - American Water Works Association. The action becomes effective on the first day of the month following the month of Journal - American Water Works Association publication of the official notice. American National Standard An American National Standard implies a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether that person has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standard. Ameri- can National Standards are subject to periodic review, and users are cautioned to obtain the latest editions. Producers of goods made in conformity with an American National Standard are encouraged to state on their own responsibility in advertising and promotional materials or on tags or labels that the goods are produced in conformity with particular American National Standards. Caution notiCe: The American National Standards Institute (ANSI) approval date on the front cover of this standard indicates completion of the ANSI approval process. This American National Standard may be revised or withdrawn at any time. ANSI procedures require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of ANSI approval. Purchasers of American National Standards may receive current information on all standards by calling or writ- ing the American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036; (212) 642-4900, or emailing [email protected]. ISBN-13, print: 978-1-58321-906-5 eISBN-13, electronic: 978-1-61300-201-8 ISBN-10, print: 1-58321-906-4 eISBN-10, electronic: 1-61300-201-7 All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopy, recording, or any information or retrieval system, except in the form of brief excerpts or quotations for review purposes, without the written permission of the publisher. Copyright © 2012 by American Water Works Association Printed in USA ii Copyright © 2012 American Water Works Association. All Rights Reserved. Committee Personnel The Steel Water Pipe Manufacturer’s Technical Advisory Committee (SWPMTAC) Task Group on AWWA C200 which reviewed and revised this standard, had the following personnel at the time: Brent Keil, Chair S.A. Arnaout, Hanson Pressure Pipe Inc., Dallas, Texas (AWWA) H.H. Bardakjian, Mfg. Consultant, Glendale, Calif. (AWWA) R.J. Card, Mfg. Consultant, Sugar Hill, Ga. (AWWA) R.J. Carpenter, American SprialWeld Pipe Company, Birmingham, Ala. (AWWA) D. Dechant, Mfg. Consultant, Aurora, Colo. (AWWA) A. Fletcher, Tyco Water Technologies, Southbank, VIC, Australia (AWWA) B.D. Keil, Northwest Pipe Company, Pleasant Grove, Utah (AWWA) J.L. Luka, American SpiralWeld Pipe Company, Columbia, S.C. (AWWA) R.D. Mielke, Northwest Pipe Company, Raleigh, N.C. (AWWA) J. Olmos, Ameron International, Rancho Cucamonga, Calif. (AWWA) G.F. Ruchti, Mfg. Consultant, Punta Gorda, Fla. (AWWA) R.N. Satyarthi, Baker Coupling Company Inc., Los Angeles, Calif. (AWWA) B.F. Vanderploeg, Mfg. Consultant, Portland, Ore. (AWWA) D.R. Wagner, Mfg. Consultant, Saint Louis, Mo. (AWWA) R. Warner, National Welding Corporation, Midvale, Utah (AWWA) B.N. Williams, National Welding Corporation, Midvale, Utah (AWWA) The AWWA Standards Committee on Steel Pipe, which reviewed and approved this standard, had the following personnel at the time of approval: John H. Bambei Jr., Chair Dennis Dechant, Vice-Chair John L. Luka, Secretary General Interest Members W.R. Brunzell, Brunzell Associates Ltd., Skokie, Ill. (AWWA) R.J. Card, Lockwood Andrews & Newnam, Sugar Hill, Ga. (AWWA) R.L. Coffey, HDR Engineering Inc., Omaha, Neb. (AWWA) H.E. Dunham, MWH Inc., Bothell, Wash. (AWWA) iii Copyright © 2012 American Water Works Association. All Rights Reserved. S.N. Foellmi, Black & Veatch Corporation, Irvine, Calif. (AWWA) R.L Gibson, Freese and Nichols Inc., Fort Worth, Texas (AWWA) M.B. Horsley,* Horsley Engineering LLC, Overland Park, Kan. (AWWA) J.K. Jeyapalan, Pipeline Consultant, New Milford, Conn. (AWWA) R.A. Kufaas, Norske Corrosion & Inspection Services Ltd., Surrey, B.C. (AWWA) J.L. Mattson, Corrosion Control Technologies, Sandy, Utah (AWWA) W.J. Moncrief,* HDR Engineering Inc., San Diego, Calif. (AWWA) E.N. Olson,† Standards Council Liaison, Brown and Caldwell, Gold Hill, Ore. (AWWA) R. Ortega,* Lockwood Andrews & Newnam, Houston, Texas (AWWA) E.S. Ralph,† Standards Engineer Liaison, AWWA, Denver, Colo. (AWWA) A.E. Romer, AECOM, Newport Beach, Calif. (AWWA) J.R. Snow,* MWH Americas Inc., Denver, Colo. (AWWA) H.R. Stoner, Consultant, North Plainfield, N.J. (AWWA) C.C. Sundberg, CH2M HILL Inc., Issaquah, Wash. (AWWA) W.R. Whidden, Woolpert, Orlando, Fla. (AWWA) Producer Members S.A. Arnaout, Hanson Pressure Pipe Inc., Dallas, Texas (AWWA) H.H. Bardakjian, Consultant, Glendale, Calif. (AWWA) M. Bauer, Tnemec Company Inc., North Kansas City, Mo. (AWWA) R.R. Carpenter, American SpiralWeld Company, Birmingham, Ala. (AWWA) D. Dechant, Dechant Infrastructure Service, Aurora, Colo. (AWWA) W.B. Geyer, Steel Plate Fabricators Association, Lake Zurich, Ill. (SPFA) B.D. Keil, Northwest Pipe Company, Pleasant Grove, Utah (AWWA) J.L. Luka,* American SpiralWeld Pipe Company, Columbia, S.C. (AWWA) R. Mielke,* Northwest Pipe Company, Raleigh, N.C. (AWWA) J. Olmos, Ameron International, Rancho Cucamonga, Calif. (AWWA) J.A. Wise, Canus International Sales Inc., Surrey, B.C. (AWWA) User Members G.A. Andersen, New York City Bureau of Water Supply, Little Neck, N.Y. (AWWA) J.H. Bambei Jr., Denver Water, Denver, Colo. (AWWA) B. Cheng, Metro Vancouver, Vancouver, B.C. (AWWA) * Alternate † Liaison, nonvoting iv Copyright © 2012 American Water Works Association. All Rights Reserved. R.V. Frisz, US Bureau of Reclamation, Denver, Colo. (BUREC) G. George, Tacoma Water, Water Supply Section, Tacoma, Wash. (AWWA) T.J. Jordan, Metropolitan Water District of Southern California, La Verne, Calif. (AWWA) M. McReynolds,* Metropolitan Water District of Southern California, La Mirada, Calif. (AWWA) G. Oljaca,* Greater Vancouver Regional District, Burnaby, B.C. (AWWA) G.P. Stine, San Diego County Water Authority, San Diego, Calif. (AWWA) N.A. Wigner, Los Angeles Department of Water & Power, Los Angeles, Calif. (AWWA) J.V. Young, City of Richmond, Richmond, B.C. (AWWA) * Alternate v Copyright © 2012 American Water Works Association. All Rights Reserved. This page intentionally blank. Copyright © 2012 American Water Works Association. All Rights Reserved. Contents All AWWA standards follow the general format indicated subsequently. Some variations from this format may be found in a particular standard. SEC. PAGE SEC. PAGE Foreword 4.6 Pipe Made to ASTM or I Introduction. ......................................ix API Requirements .......................10 I.A Background ........................................ix 4.7 Fabricated Pipe ..................................10 I.B History .............................................ix 4.8 Selection of Materials ........................13 I.C Acceptance ..........................................x 4.9 Fabrication of Pipe ............................13 II Special Issues. .....................................xi 4.10 Requirements for Welding II.A Advisory Information on Product Operations ..................................14 Application. ..................................xi 4.11 Permissible Variations in III Use of This Standard .........................xii Dimensions .................................20 III.A Purchaser Options and 4.12 Preparation of Ends ...........................21 Alternatives ................................xiii 4.13 Special Sections .................................26 III.B Modification to Standard .................xiii 4.14 Fabrication of Special Sections...........26 IV Major Revisions ................................xiii 5 Verification V Comments ........................................xv 5.1 Inspection .........................................26 5.2 Test Procedures .................................27 Standard 5.3 Calibration of Equipment ..................29 1 General 5.4 Test Reports ......................................30 1.1 Scope ..................................................1 6 Delivery 1.2 Purpose ...............................................1 6.1 Marking ............................................30 1.3 Application ..........................................1 6.2 Handling and Loading ......................30 2 References ..........................................2 6.3 Affidavit of Compliance ....................30 3 Definitions .........................................5 Figures 4 Requirements .....................................8 1 Charpy Test Evaluation .....................12 4.1 Permeation ..........................................8 2 Bridge Cam Gauge ............................14 4.2 Materials and Workmanship ...............9 3 Repair Method by Offset Value and 4.3 Drawings .............................................9 Wall Thickness ............................15 4.4 Calculations ........................................9 4 Reduced-Section Tension Test 4.5 Protective Coating .............................10 Specimen .....................................17 vii Copyright © 2012 American Water Works Association. All Rights Reserved. 5 Guided-Bend Test Specimen .............17 Tables 1 Steel Plate, Sheet, or Coils for 6 Jig for Guided-Bend Test ...................18 Fabricated Pipe ............................11 7 Alternative Guided-Bend Wraparound 2 Repair Requirements Based on Offset Jig ...............................................19 Value and Wall Thickness ............15 8 Alternative Guided-Bend Roller Jig ...19 3 Guided-Bend Test Jig Dimensions .....18 viii Copyright © 2012 American Water Works Association. All Rights Reserved. Foreword This foreword is for information only and is not a part of ANSI*/AWWA C200. I. Introduction. I.A. Background. This standard covers butt-welded, straight-seam or spiral- seam steel pipe, 6 in. (150 mm) and larger, for transmission and distribution of water, including fabrication of pipe, requirements of welding operations, permissible variations of thickness and dimensions, preparation of ends, fabrication of special sections, inspection, and test procedures. I.B. History. The first AWWA steel pipe standards issued were 7A.3 and 7A.4, published in 1940. Standard 7A.4 pertained to steel pipe smaller than 30 in. (750 mm) in diameter, and 7A.3 pertained to steel pipe 30 in. ( 750 mm) in diameter and larger. Subsequently, in recognition that some pipe used in water utility service was manufactured in steel mills rather than in a fabricator’s shop, two new AWWA standards were issued in 1960. AWWA C201 replaced 7A.3 and pertained to all pipe, regardless of diameter, manufactured in a fabricator’s shop from steel sheet or plate. The physical and chemical properties are properties of the sheet or plate from which the pipe is made. The properties are a function of the steel mill practice and are not affected significantly by fabricating procedures. AWWA C202 replaced 7A.4 and pertained to mill pipe, which is normally produced in a production pipe mill. The specified physical and chemical properties are those of the completed pipe. Physical testing is performed on the pipe rather than on the steel from which it originates. In many cases, the physical properties are significantly affected by the pipe-manufacturing procedure. AWWA C201 was revised in 1966, and AWWA C202 was revised in 1964. Both AWWA C201 and AWWA C202 were superseded by AWWA C200-75, approved by the AWWA Board of Directors on Jan. 26, 1975. AWWA C200 includes all types and classes of steel pipe, 6 in. (150 mm) in diam- eter and larger, used in water utility service, regardless of the pipe manufacturing source. With adequate quality assurance, pipe manufactured in a fabricator’s shop or in a steel pipe mill is suitable for water utility service. By reference, AWWA C202 (which pertained to mill-type steel water pipe) included API† 5L and API 5LX pipe grades manufactured to API standards for high-pressure * American National Standards Institute, 25 West 43rd Street, Fourth Floor, New York, NY 10036. † American Petroleum Institute, 1220 L Street N.W., Washington, DC 20005. ix Copyright © 2012 American Water Works Association. All Rights Reserved.