FluidMechanics: OpenAcces s Fluid Mechanics: Open Access Teja et al., Fluid Mech Open Acc 2016, 3:1 ISSN: 2476-2296 Research Article Open Access Analysis of Exhaust Manifold using Computational Fluid Dynamics Marupilla Akhil Teja*, Katari Ayyappa, Sunny Katam and Panga Anusha SIR C R Reddy College of Engineering, Andhra University, Vizag, India Abstract Overall engine performance of an engine can be obtained from the proper design of engine exhaust systems. With regard to stringent emission legislation in the automotive sector, there is a need design and develop suitable combustion chambers, inlet, and outlet manifold. Exhaust manifold is one of the important components which affect the engine performance. Flow through an exhaust manifold is time dependent with respect to crank angle position. In the present research work, numerical study on four-cylinder petrol engine with two exhaust manifold running at constant speed of 2800 rpm was studied. Flow through an exhaust manifold is dependent on the time since crank angle positions vary with respect to time. Unsteady state simulation can predict how an intake manifold work under real conditions. The boundary conditions are no longer constant but vary with time. The main objectives that to be studied in this work is: • To prepare the cad model in the CATIA software by using the actual parametric dimensions. • To prepare finite element model in the Computer aided analysis software by specifying the approximate element size for meshing. • To find and calculate the actual theoretical values for the input boundary conditions. • To study the flow patterns generated due to the flow of the exhaust gases from the manifold. • To study the velocity and pressure distribution in ports at maximum flow rate. • To study the static pressure drop, total pressure drop, and energy loss in the flow pattern generated in the exhaust manifold. Keywords: Exhaust-manifold; Computational fluid dynamics; Back- pressure Introduction Exhaust manifold The exhaust manifold is a pipe, receives the exhaust gases from the combustion Chamber and leaves it to the atmosphere. Exhaust manifolds are mounted to the cylinder head. V- Type engines have Figure 1: Log type manifold. two exhaust manifolds, and an in-line engine usually has one. When intake and exhaust manifolds are on opposite sides of an in-line engine, drag racing will use a long runner tubular manifold, which will favor the head is called a cross-flow head. This design improves breathing flow in the upper rev range. Tubular manifolds are very efficient when capacity of an engine. Exhaust manifolds are typically made of cast iron compared to a log manifold. They offer superior flow characteristics, or steel, although some latest-model cars use stainless steel manifolds. and offer less back flow of exhaust gases back into the Motor. Now for Cast iron is a good material for exhaust manifolds. Like the frying pan the negative tubular manifolds are often prone to cracking causing them on a stove, it can tolerate fast and severe temperature changes. Exhaust gas temperature is related to the amount of load on the engine. to lose points in the reliability column. For those focused on getting the most performance they can, a tubular manifold is a must (Figure 2). Types of turbo manifolds (a)Single scroll manifold: A single scroll manifold is one where all Log manifold: The log type manifold is the most economical the exhaust runners come to a common collector where they enter the manifold on the market. They are almost bullet proof when it comes turbocharger. Also all the runners share a common waste gate to expel to reliability and they are the most compact manifolds available. Most exhaust gases. This is the most common type of tubular manifold. manifolds you find on factory turbocharged cars are log type manifolds. This is understandable when you (Figure 1) manufacturer is all about (b) Twin Scroll or divided manifold: A twin scroll manifold reliability. When it comes to performance, a log manifold will leave you wanting. All of the exhaust gases flow into a common way where they often collide with each other causing a lot of turbulence before *Corresponding author: Teja AM, SIR C R Reddy College of Engineering, Andhra the turbo. This hurts the turbo’s performance and hurts the motors University, Vizag, India, Tel: 5712300489; E-mail: [email protected] performance as well being that a log manifolds common plenum is so Received July 07, 2016; Accepted July 17, 2016; Published July 28, 2016 close to the other cylinders, it causes a lot of back flow of exhaust. Citation: Teja MA, Ayyappa K, Katam S, Anusha P (2016) Analysis of Exhaust Tubular manifold: A tubular manifold is one that is custom made for Manifold using Computational Fluid Dynamics. Fluid Mech Open Acc 3: 129. that particular user’s goal for the car. Most road racing cars will build Copyright: © 2016 Teja MA, et al. This is an open-access article distributed under an average runner, equal length manifold that will support great flow the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and characteristics throughout the entire rev range. A car being set-up for source are credited. Fluid Mech Open Acc Volume 3 • Issue 1 • 1000129 ISSN: FMOA, an open access journal Citation: Teja MA, Ayyappa K, Katam S, Anusha P (2016) Analysis of Exhaust Manifold using Computational Fluid Dynamics. Fluid Mech Open Acc 3: 129. Page 2 of 16 positive. Energy must be used up in order to overcome the initial positive (back) pressure in the exhaust system before the exhaust gas is pushed out of the combustion chamber. Further we must be able to overcome the positive backpressure. It well known that, the exhaust gas begins to travel faster and creates a NEGATIVE pressure (Figure 3). In the figure 1 the pressure tracing is downward or has a negative value. When it is with a more negative pressure, then it means that, there is creation of more suction or a vacuum in the system. The system is literally sucking or pulling out exhaust gas from the combustion Figure 2: Tubular manifold. chamber or cylinder. This sucking or "SCAVENGING" affect not only helps to remove more exhaust gas from the cylinder. It also helps to is designed for the most ideal exhaust flow a motor can offer. These suck more intake air and fuel mixture. Faster the exhaust gas travel manifolds are built so that runners that come together are paired to be more will be the vacuum creation. However, it is necessary to have 180 degrees apart from each other on their firing order. This is done much as negative pressure creation before cam overlaps. so that there is little chance of exhaust flow interference from another cylinders exhaust gases. This not only helps the motor to better expel its Exhaust pulses and energy pulses exhaust, but also helps to keep the exhaust velocity as high as possible, To understand how a typical exhaust system works, you first have aiding in the turbochargers spool and the motors torque output. A twin to understand what exhaust pulses are. As for the exhaust manifold, its scroll manifold must be used with a turbo that is equipped with a twin job is simple: to contain the gases that leave the cylinder head’s exhaust scroll housing that keeps the exhausts divided all the way to the turbo’s ports just after each power stroke. These gases exit the ports in the exhaust wheel. form of pulses, high-speed, high-pressure pulses created by the piston Factors to be considered during the design and development moving upward thus squishing everything out. The piston creates the of exhaust manifold pressure, but said pressure disappears once the exhaust valves close. Surrounding each exhaust pulse on a well-designed header is a large Runner length: This is arguably one of the most important factors. pressure differential with more pressure in front of the pulse than First would be to make sure that the runners are as equal length as behind it – this is due to the valve closing. This pressure differential possible. The idea being that the exhaust pulses will be spaced out actually assists in evacuating the exhaust gases most efficiently. The evenly and arriving at the turbine wheel on the turbo at their own time process is as follows: once the high-speed, high-pressure exhaust gases in the firing order. If they arrive sooner or later, they may interfere with exit past the exhaust valves, a low-pressure zone is left behind; in the the exhaust pulses from the next firing cylinder. Next, a longer runner best scenarios it not only leaves low pressure, but also leaves the negative manifold will have better flow up top, while a shorter manifold can yield pressure in the form of a vacuum. If you can control when this negative a faster spool, with also less transient lag. pressure referred to as the vacuum reaches the port then you can expect Runner volume: Runner volume needs to be considered when significant power gains. The process relies on the inertia created by the building a turbo manifold. While a larger runner diameter does fast-moving gases. When strong enough, the inertia can actually help facilitate lower exhaust backpressure for better flow on the top-end, it coerce gases through the open valves during overlap periods. A side does cause a lower exhaust velocity. A lower exhaust velocity will cause from the exhaust gas pulses, there’s another kind of pulse going on here. longer spool times, and less transient response out of the turbo. Sound waves are also emitted into the manifold each time an exhaust valve opens up. Collectors: A collector’s job is to tie all of the cylinder’s pipes together in one common place and send them into a single exit pipe. Traveling at the speed of sound, these waves move at a quicker rate than the exhaust pulses do. Also in contrast to exhaust pulses, pressure A collector is generally a conglomeration of pipes all merged together, waves bounce around within the pipes, and depending upon diameter allowing for a smooth transition from the primaries or secondaries into changes and a number of other factors, they may often revert direction. the rest of the exhaust. When properly constructed, a good collector The results are exhaust gas pulses traveling in one direction and low- will take the low pressure waves created earlier and send them back up the primaries, thus quickening the entire evacuation process. There are two scenarios in which exiting exhaust gases will encounter once they move past the valve: low-pressure or high-pressure. Low-pressure Main Pressure Wave situations within the exhaust pipes help promote better flow by allowing Overlap Period for increased velocity through the exhaust ports while high-pressure situations do the opposite. Back pressure: Back pressure can be produced at two places, i.e., Negative Pressure “suction” behind when the exhaust valve opens and cam overlap taking place shown in main wave TDC figure 2. Pressure measurements at the exhaust valve during the start of the exhaust stroke at bottom dead centre (BDC) to cam overlap at BDC the end of the exhaust stroke/beginning of the intake stroke at top dead centre (TDC). Notice the positive (backpressure) spike at the exhaust valve opens far left as the exhaust valve just opens at BDC. The exhaust gases Rarefraction on must now push against this POSITIVE (back) pressure before it can leave the combustion chamber. The pressure tracing is upwards and Figure 3: Exhaust valve pressure measurement. Fluid Mech Open Acc Volume 3 • Issue 1 • 1000129 ISSN: FMOA, an open access journal Citation: Teja MA, Ayyappa K, Katam S, Anusha P (2016) Analysis of Exhaust Manifold using Computational Fluid Dynamics. Fluid Mech Open Acc 3: 129. Page 3 of 16 pressure energy waves bouncing around all over the place. If the workbench with the only difference that the tools in this environment manifold can allow for these low-pressure energy waves to arrive back are used to create basic and advanced surfaces. at the exhaust valves just as they once again open, the whole process Assembly design workbench: The Assembly Design workbench can be used to the engine’s advantage. But this requires everything to is used to assemble the components using the assembly constraints be timed correctly and this is nothing short of difficult to figure out available in this workbench. There are two types of assembly design sometimes. approaches: Introduction to CATIA V5R20 1. Bottom-up Welcome to CATIA (Computer Aided Three Dimensional 2. Top-down Interactive Application). As a new user of this software package, you will join hands with thousands of users of this high-end CAD/CAM/ • In the bottom-up approach of the assembly design, the CAE tool worldwide. If you are already familiar with the previous components are assembled together to maintain their design releases, you can upgrade your designing skills with the tremendous intent. improvement in this latest release. • In the top-down approach, components are created inside the CATIA V5, developed by Dasssault Systems, France, is a completely assembly in the Assembly Design workbench. You can also re-engineered, Next-generation family of CAD/CAM/CAE software assemble an existing assembly to the current assembly. solutions for Product Lifecycle Management. Through its exceptionally • The Space Analysis toolbar provides the Clash analysis tool easy-to-use and state-of-the-art user interface, CATIA V5 delivers that helps in detecting clash, clearance, and contact between innovative technologies for maximum productivity and creativity, from the inception concept to the final product. CATIA V5 reduces components and sub-assemblies. the learning curve, as it allows the flexibility of using feature-based and Drafting workbench: The Drafting workbench is used for the parametric designs. documentation of the parts or assemblies created earlier in the form CATIA V5 provides three basic platforms: P1, P2, and P3. P1 is for of drawing views and their detailing. There are two types of drafting small and medium-sized process-oriented companies that wish to grow techniques: toward the large scale digitized product definition. • Generative drafting P2 is for the advanced design engineering companies that require • Interactive drafting product, process, and resource modeling. P3 is for the high-end design applications and is basically for Automotive and Aerospace Industry, The generative drafting technique is used to automatically generate where high quality surfacing or Class-A surfacing is used. The subject the drawing views of the parts and assemblies. The parametric of interpretability offered by CATIA V5 includes receiving legacy dimensions added to the component in the Part Design workbench data from the other CAD systems and even between its own product during its creation can be generated and displayed automatically in the data management modules. The real benefit t is that the links remain drawing views. The generative drafting is bidirectional associative in associative. As a result, any change made to this external data gets nature. You can also generate the Bill of Material (BOM) and balloons notified and the model can be updated quickly. in the drawing views. CATIA V5 workbenches: CATIA V5 serves the basic design tasks In interactive drafting, you need to create the drawing views by by providing different workbenches. A workbench is defined as a sketching them using the normal sketching tools and then adding the specified environment consisting of a set of tools that allows the user dimensions. to perform specific design tasks. The basic workbenches in CATIA V5 Generative sheet metal design workbench: The Generative Sheet are Part Design, Wireframe and Surface Design, Assembly Design, metal Design workbench is used for the designing the sheet metal Drafting. components. Generally, the solid models of the sheet metal components Part design workbench: The Part design workbench is a parametric are created to generate the flat pattern of the sheet, study the design and feature-based environment in which you can create solid models. of the dies and punches, study the process plan for designing, and the The basic requirement for creating a solid model in this workbench is a tools needed for manufacturing the sheet metal components. sketch. The sketch for the features is drawn in the Sketcher workbench that can be invoked within the Part Design workbench. You can draw Introduction to ANSYS the sketch using the tools in this workbench. While drawing a sketch, ANSYS is a large-scale multipurpose finite element program some constraints are automatically applied to it. You can also apply developed and maintained by ANSYS Inc. to analyze a wide spectrum additional constraints and dimensions manually. After drawing the of problems encountered in engineering mechanics. sketch, exit the Sketcher workbench and convert it into a feature. The tools in the Part Design workbench can be used to convert the sketch Program organization: The ANSYS program is organized into two into a sketch-based feature. This workbench also provides other tools basic levels: to apply the placed features, such as fillets, chamfers, and so on. These • Begin level features are called the dress-up features. You can also assign materials to the model in this workbench. • Processor (or Routine) level Wireframe and surface design workbench: The Wireframe and The Begin level acts as a gateway into and out of the ANSYS program. Surface Design workbench is also a parametric and feature-based It is also used for certain global program controls such as changing the environment, and is used to create wireframe or surface models. job name, clearing (zeroing out) the database, and copying binary files. The tools in this workbench are similar to those in the Part Design When you first enter the program, you are at the Begin level. Fluid Mech Open Acc Volume 3 • Issue 1 • 1000129 ISSN: FMOA, an open access journal Citation: Teja MA, Ayyappa K, Katam S, Anusha P (2016) Analysis of Exhaust Manifold using Computational Fluid Dynamics. Fluid Mech Open Acc 3: 129. Page 4 of 16 • At the Processor level, several processors are available. Each • Coupled-field loads are simply a special case of one of the processor is a set of functions that perform a specific analysis above loads, where results from one analysis are used as loads task. For example, the general pre-processor (PREP7) is where in another analysis. For example, you can apply magnetic you build the model, the solution processor (SOLUTION) is forces calculated in a magnetic field analysis as force loads in a where you apply loads and obtain the solution, and the general structural analysis. postprocessor (POST1) is where you evaluate the results of a Analysis types: The following types of analysis are possible using solution. An additional postprocessor, POST26, enables you ANSYS to evaluate solution results at specific points in the model as a function of time. • Structural Analysis: Static Analysis, Modal Analysis, Harmonic Analysis, Transient Dynamic Analysis, Spectrum Analysis, Material models: ANSYS allows several different material models Buckling Analysis, Explicit Dynamic Analysis, Fracture like: mechanics, and Beam Analysis. • Linear elastic material models (isotropic, orthotropic, and anisotropic). • Thermal Analysis: Steady-state thermal analysis, transient thermal analysis. • Non-linear material models (hyper elastic, multi linear elastic, inelastic and Visco elastic). • CFD (Computational Fluid Dynamics) Analysis: Laminar or turbulent, Thermal or adiabatic, Free surface, Compressible • Heat transfer material models (isotropic and orthotropic). or incompressible, Newtonian or Non-Newtonian, Multiple • Temperature dependent material properties and Creep material species transport. models. • Several types of Electromagnetic field analysis and Coupled Loads: The word loads in ANSYS terminology includes boundary field analysis. conditions and externally or internally applied forcing functions, as Post processing: Post processing means reviewing the results of an illustrated in Loads. Examples of loads in different disciplines are: analysis. It is probably the most important step in the analysis, because Structural: displacements, forces, pressures, temperatures (for you are trying to understand how the applied loads effect your design, thermal strain), Gravity. how good your finite element mesh is, and so on Two postprocessors are available to review your results: POST1, the general Postprocessor, and Thermal: temperatures, heat flow rates, convections, internal heat POST26, the time-history postprocessor. POST1 allows you to review generation, Infinite surface. the results over the entire model at specific load steps and sub steps (or Magnetic: magnetic potentials, magnetic flux, magnetic current at specific time points or frequencies). POST26 allows you to review segments, source current density, and infinite surface. the variation of a particular result item at specific points in the model with respect to time, frequency, or some other result item. In a transient Electric: electric potentials (voltage), electric current, electric magnetic analysis, for instance, you can graph the eddy current in a charges, charge densities, infinite surface. particular element versus time. Or, in a nonlinear structural analysis, Fluid: velocities, pressures Loads are divided into six categories: you can graph the force at a particular node versus its deflection. DOF constraints, forces (concentrated loads), surface loads, body Literature Review loads, inertia loads, and coupled field loads. • A DOF constraint fixes a degree of freedom (DOF) to a known Specifications of Kawasaki Z 750 value. Examples of constraints are specified displacements Displacement: 748.00 cc and symmetry boundary conditions in a structural analysis, prescribed temperatures in a thermal analysis, and flux-parallel Engine type: In-line four,four stroke boundary conditions. Power: 104.20hp (76.1kw) @10500 rpm • A force is a concentrated load applied at a node in the model. Torque: 78 Nm @ 8000 rpm Examples are forces and moments in a structural analysis, heat flow rates in a thermal analysis, and current segments in a Compression ratio: 11.3:1 magnetic field analysis. Bore*stroke: 68.4*50.9 mm • A surface load is a distributed load applied over a surface. Valves per cylinder: 4 Examples are pressures in a structural analysis and convections and heat fluxes in a thermal analysis. Fuel system: Injection • A body load is a volumetric or field load. Examples are Ignition: digital temperatures and fluencies in a structural analysis, heat Cooling system: liquid generation rates in a thermal analysis, and current densities in a magnetic field analysis. Global journal of researches in engineering • Inertia loads are those attributable to the inertia (mass matrix) The numerical formulation of the problem is incomplete of a body, such as gravitational acceleration, angular velocity, without prescribing boundary conditions, which correspond to the and angular acceleration. You use them mainly in a structural specific physical model. The specification of mathematically correct analysis. boundary conditions that ensure the uniqueness of the solution, while Fluid Mech Open Acc Volume 3 • Issue 1 • 1000129 ISSN: FMOA, an open access journal Citation: Teja MA, Ayyappa K, Katam S, Anusha P (2016) Analysis of Exhaust Manifold using Computational Fluid Dynamics. Fluid Mech Open Acc 3: 129. Page 5 of 16 being compatible with the physics at the boundaries, is not always The disadvantage is back pressure can be created in the exhaust straightforward. Before arriving at the boundary conditions at various system. All engines have a maximum allowable engine back pressure boundaries, we have to first identify the solution/computational domain specified by the engine manufacturer [6]. Sometimes it will be high of the problem [1]. The physical domain and computational domain so that may cause some effects on the diesel engine. So this project is usually differ. However, the computational domain largely depends on aimed to reduce the back pressure in the exhaust silencer by using the the geometry of physical domain. The computational domain boundary software computational fluid dynamics (CFD) the back pressure will (truncated from the real boundary) along with appropriate boundary be reduced. conditions should be chosen in such a way that there is negligible Geometric Modeling and Analysis change in the results with further increase in its size. International journal of automobile engineering Drawing details Exhaust manifold is one of the most critical components of an IC The four-into-one configured exhaust manifold gets its name from Engine. The designing of exhaust manifold is a complex procedure and its shape and design, four individual ports exiting the cylinder head is dependent on many parameters viz. back pressure, exhaust velocity, which all meet up to a single collector as shown in (Figures 4.1- 4.8). mechanical efficiency etc. Preference for any of this parameter varies Four-into-one configured exhaust manifolds are generally restricted as per designer’s needs. Usually fuel economy, emissions and power for high-speed application. The IGES files imported in ICEM, model requirement are three different streams or thought regarding exhaust of all inlet and outlet ports length extended for flow develop (Figures manifold design. This work comprehensively analyzes eight different 4.1- 4.8). The thickness of the exhaust manifold deleted to obtain fluid models of exhaust manifold and concludes the best possible design domain. The conversion of 2d drafting to 3d model in CATIA software for least emissions and complete combustion of fuel to ensure least is known as 3d modeling. The 3d model designed is in STP format pollution [2]. (Figures 5 and 6). Fluent 6.0 provides three mesh motion strategies to accommodate ANSYS ICEM CFD the volume deformation associated with in-cylinder motion: spring ANSYS ICEM CFD meshing software starts with advanced CAD/ smoothing, local re-meshing, and dynamic layering. A common feature geometry readers and repair tools that allow the user to quickly move to of each of these modes of deformation is that the cell topology and node a variety of geometrytolerant meshes and produce high-quality volume movement of interior cells and nodes is determined automatically by or surface meshes with minimal effort. Advanced mesh diagnostics, the solver. The user only needs to specify motion at the boundaries, interactive and automated mesh editing, output to a wide variety of the internal structure of the mesh is determined by the solver at each CFD and FEA solvers, and multi-physics post-processing tools make timestep in response to the prescribed boundary motion [3]. the ANSYS ICEM CFD tool a complete meshing solution. The product vision is to provide a variety of flexible tools that can take the model Among the cyclic plasticity models, overlay model have been from any geometry to any solver, in one modern and fully scriptable considered as physically motivated, as many real materials or environment. Features include: Intuitive built-in geometry creation and mechanical systems can be thought of as having a similar structure. highly automated. For example, most of the engineering materials may have a crystalline structure that is made of a distribution of slip-planes or dislocations of Functionality for the modification and repair of imported CAD different slip strengths [4]. The overlay model has definite advantages data. Ability to work with both NURBs and faceted geometry types over the classical models. The varieties of effects which cannot be like STL or existing meshes. Robust tools for creating all mesh types: described in the classical models can be done in the overlay model, hexahedral, tetrahedral, prism, pyramid, quad, tri or bar elements. whereby the description remains fairly simple and qualitative. The basic Highly tolerant of imperfect/over detailed CAD data containing sliver assumption of overlay model is that material is composed of a series of surfaces, gaps, holes and overlaps (patch independence). Supports so-called Jenkin’s elements connected in parallel, each of which consists Smoothing, coarsening, refinement, and element type conversion, of a linear spring with stiffness [5]. linear or quadratic element. More than 100 CFD/CAE solver interface Figure 4.1: Central tube. Figure 4.2: Cylinder to exhaust coupling. Fluid Mech Open Acc Volume 3 • Issue 1 • 1000129 ISSN: FMOA, an open access journal Citation: Teja MA, Ayyappa K, Katam S, Anusha P (2016) Analysis of Exhaust Manifold using Computational Fluid Dynamics. Fluid Mech Open Acc 3: 129. Page 6 of 16 Figure 4.3: Exhaust center. Figure 4.6: Main way. Figure 4.4: Finale cap. Figure 4.7: Subway. Figure 4.5: Initial cap. formats. File based transfer of CFD and structural results for Fluid structure interaction simulations. Automated batch processing through an intuitive scripting framework (Figure 7). Figure 4.8: Tubes. Mesh generation approach To analyze fluid flow in an area of interest, the partial differential Grid generation is an essential tool in computational simulation of equations (Euler equations, Navier-Stokes etc.) need to be solved. These physical field phenomena and process. Unfortunately, grid generation equations cannot be solved for the entire region at once except for the process is not unique; it can be seen something which involves art very simple cases. So, in order to get numerical solution describing fluid as well as science. Therefore, it requires intensive user interaction in flow in a domain, the domain must be split into smaller sub domains selection and development of high quality reliable grid. Automation called cells or elements and equations are solved for each of these of grid generation process requires understanding of the underlying cells. Collection of these cells in a region is called Mesh or Grid and principles, mathematics and technology involved in the process and the process of splitting the domain into cells is called mesh generation. a careful analysis of problem domain. In 2D case domain is split into Fluid Mech Open Acc Volume 3 • Issue 1 • 1000129 ISSN: FMOA, an open access journal Citation: Teja MA, Ayyappa K, Katam S, Anusha P (2016) Analysis of Exhaust Manifold using Computational Fluid Dynamics. Fluid Mech Open Acc 3: 129. Page 7 of 16 Figure 5: Exhaust assembly. Figure 6: Exploded view of exhaust manifold. quadrilaterals and triangular cells and for 3D case in hexahedral and  From users point of view, they possess high degree of control. tetrahedral cells shown in (Figure 8). For example user can easily control the refinement level in a particular region by placing more dense points on the Mesh classification: Mesh can be classified on the bases of boundaries of that region. connectivity of the elements as follows:  Memory requirement to simulate flow in a structured domain Structured mesh: Structured meshes are widely used in many is less as compared to other methods. real CFD applications. In structure mesh all interior vertices are topologically alike. This can be generated algebraically by interpolation  Element could easily be flow aligned in structured meshes from boundaries for example transfinite interpolation. In structured which offer more accuracy of the results. meshes points are laid in the region of interest in a regular pattern; these points form quadrilateral cells in 2D and hexahedral in 3D. A  Examination of flow field in post processing is easier with structured mesh generated in 2D region is shown in (Figure 9). structured mesh. There are some significant advantages associated with structured Unstructured mesh meshes due to which they are preferred over other grid methods in Unstructured meshes are used in many FEA and CFD applications many applications. These advantages are listed below: which have irregular shape of object or region of interest. Unlike  From the solver point of view, they have simplicity and easy structured mesh, they can have elements of arbitrary topology in a data access. confined region. In unstructured meshes points are laid in the region of Fluid Mech Open Acc Volume 3 • Issue 1 • 1000129 ISSN: FMOA, an open access journal Citation: Teja MA, Ayyappa K, Katam S, Anusha P (2016) Analysis of Exhaust Manifold using Computational Fluid Dynamics. Fluid Mech Open Acc 3: 129. Page 8 of 16 Figure 7: Imported file from CATIA to CFX. interest in a random order forming triangular subdivision of the region. Unstructured mesh in its most basic form contains triangles in 2D and tetrahedral cells in 3D, but may be made of hexahedral or elements of any shape in general. Unstructured meshes are more easily generated and adapted but require a much more complex solution data structure. In generation of unstructured mesh user control is limited as interior nodes are generated automatically without any interaction of user. An unstructured mesh generated around airfoil in 2D region is shown in (Figure 10). Figure 8: Example of 2D analysis domain. The advantages of unstructured grid methods are given below:  They have the ability to adopt better around the complex geometries.  They can be generated with less efforts and interactions.  They can be easily adopted by the applications which require automation of the mesh generation process . Hybrid mesh: General configurations can conceivably be treated with either type of mesh, and hybrid combinations are also possible, using individual structured meshes near boundaries, with the sub- regions being connected by an unstructured mesh. Thus, hybrid mesh is a positive combination of both structured and unstructured mesh and possesses the advantages of both. A hybrid mesh generated around airfoil in 2D region is shown in (Figure 11). Storage requirement per point for a flow simulation on an unstructured grid is about four times that of structured grid. Even if the unstructured grid is coarser in the far-field the storage of the un- Figure 9: Structured mesh. structured grid, with its greater total number of points would typically be 40 times greater than that for a structured grid. Thus, for hybrid Grid generation for the exhaust manifold: The exhaust manifold grid there is a clear indication that the extent of un-structured grid of IGES files imported in ICEM CFD software, the geometry cleanup employed should be as minimum as possible. has been done, the fluid domain extracted from geometry and different Grid generation approach: Grid generation is an important aspect parts were created. Unstructured mesh generated for the Exhaust as a good grid can accelerate the convergence of the solution, while a manifolds. The model-1 contains 417594 nodes and 398080 hexas, poor grid can lead to divergent iteration history. Grid generation process 38052 quads cells. The model-2 contains 413618 nodes and 394294 proceeds from first defining the boundary geometry and distribution hexas, 37692 quads cells. First layer mesh size of 0.01 mm with spacing of the points on the curves that form the edges of boundary sections. factor 1.2. After generating the mesh quality has been checked. It has A surface grid is generated on the boundary surface. Finally a volume minimum internal angle is 25 degree and determinanent is 0.4. The grid is generated in case of 3D domain. This project utilizes the power skewness and nonnegative volume has been checked before importing of commercial software ANSYS ICEM CFD to automate the process of mesh generation. the mesh in solver, the boundary conditions are defined in the ICEM Fluid Mech Open Acc Volume 3 • Issue 1 • 1000129 ISSN: FMOA, an open access journal Citation: Teja MA, Ayyappa K, Katam S, Anusha P (2016) Analysis of Exhaust Manifold using Computational Fluid Dynamics. Fluid Mech Open Acc 3: 129. Page 9 of 16 For over twenty years, it has been a leader in the CFD software for simulating fluid flow, heat and mass transfer, and a host of related phenomena involving turbulence, reactions, and multiphase flow. Fluent is state-of-the-art CFD simulation software for modeling fluid flow and heat transfer in complex geometries. Fluent provides complete mesh flexibility, including the ability to solve flow problems using unstructured meshes that can be generated about complex geometries with relative ease. Fluent is ideally suited for incompressible and compressible fluid-flow simulations for complex geometries. Fluent code solves the equation of conservationof mass, momentum, energy and other relevant fluid variables. Fluent supports different mesh/grid types like 2D-triangular/quadrilateral, 3Dtetrahedral/hexahedral/ wedge/polyhedral, and mixed (hybrid) meshes. Also FLUENT allows refining (or) coarsening grid based on the flow solution. Fluent can import mesh generated by a number of meshing software including Gambit, T Grid, Gridgen, Ansys, Ideas, ICEM, Hypermesh etc. It supports journaling which can be used in creating script files for automation of solver process. Batch and serial mode solving process is provided. Once the mesh is imported to FLUENT, governing equations Figure 10: Unstructured mesh. (in integral form) for the conservation of mass, momentum, energy and any other relevant variables are applied to each discrete control volume and used to construct a set of non-linear algebraic equations for the discrete dependent variables, Figure 12 shows each iterative pressure solver. In this thesis work all simulations are performed by pressure based. Computational fluid dynamics-working on CFD: Computational Fluid Dynamics (CFD) is the science of predicting fluid flow, heat transfer, mass transfer, chemical reactions, and related phenomena by solving the mathematical equations which govern these processes using computational methods. Computational Fluid Dynamics (CFD) is a discipline that solves a set of equations governing the fluid flow over any geometrical configuration. The particular form chosen depends on the intended application. The equation can represent steady or unsteady, compressible or incompressible, and inviscid or viscous flows, including non-ideal and reacting fluid behavior. The state of the art is characterized by the complexity of the geometry, the flow physics, and the computer time required for obtaining a solution. The Physical aspects of any fluid flow are governed by three fundamental principles: Mass is conserved; Momentum and Energy is conserved: These fundamental principles can be expressed in terms of mathematical Figure 11: Hybrid mesh. equations, which in their most general form are usually partial differential equations. The role of CFD in engineering predictions has CFD itself Fluent as a solver takes mesh file in .msh format. So the become so strong that today it may be viewed as a new third dimension generated mesh with declared boundary condition is saved according of fluid dynamics, the other two dimensions being pure experiment and to the solver input format (Figure 12). pure theory. Problem solution using fluent approach The standard k- ε model: The simplest "complete models'' of turbulence are two-equation models in which the solution of two Computational Fluid Dynamics (CFD) is a computational separate transport equations allows the turbulent velocity and length technology that has become an indispensable tool to study the dynamics scales to be independently determined. The standard κ − ε model of fluid and analyzing the fluid flow, pressure distribution, heat and falls within this class of turbulence model and has become the mass transfer etc., in a region of interest. It is a powerful numerical workhorse of practical engineering flow calculations in the time since tool used widely to simulate many processes in automobile industries. it was proposed by Launder and Spalding. Robustness, economy, Using CFD software a 'virtual prototype' of the system or device can and reasonable accuracy for a wide range of turbulent flows explain be made and applied with the real world physical conditions and then its popularity in industrial flow and heat transfer simulations. It is a prediction about the performance of that design can be obtained. semiempirical model, and the derivation of the model equations relies Recent progression in computing efficacy coupled with reduced costs on phenomenological considerations and empiricism. of CFD software packages has advanced CFD as a viable technique to Steps in CFD: CFD is structured around the numerical algorithms provide effective and efficient design solutions. that can tackle fluid flow problems. In order to provide easy access to Fluent: Fluent is commercial CFD solver software by ANSYS. their solving power these include sophisticated user interfaces to input Fluid Mech Open Acc Volume 3 • Issue 1 • 1000129 ISSN: FMOA, an open access journal Citation: Teja MA, Ayyappa K, Katam S, Anusha P (2016) Analysis of Exhaust Manifold using Computational Fluid Dynamics. Fluid Mech Open Acc 3: 129. Page 10 of 16 Figure 12: Meshed exhaust manifold. problem parameters and to examine the results. Hence all contain three Input Parameters used in CFD are: main elements. Temperature: 1500 K a) Pre-processor Pressure: 2 bar b) Solver and Mass flow rate: 0.01 kg/s c) Post-processor Output parameters used are: Pre-processor: Pre-processing consists of the input of a flow Temperature: 300 K problem to a CFD problem by means of an operator-friendly interface Pressure: 25 kpa and the subsequent transformation of this input into a form suitable for use by the solver. The user activities at the pre-processing stage involve: Considered steady state condition:  Definition of the geometry of the region of interest: the • Incompressible ideal gas as a working fluid. computational domain. • The flow was considered to be turbulent. 10% turbulent  Grid generation-the sub-division of the domain into a number intensity was taken and K-εmodel. of smaller subdomains: a grid (or mesh) of cells (or control Boundary conditions are: volumes or elements). Inlets: At an inlet, fluid enters the domain and, therefore, its fluid  Selection of the physical and chemical phenomena that need velocity or pressure or the mass flow rate may be known. Also, the fluid to be modeled. may have certain characteristics, such as the turbulence characterizes which needs to be specified.  Definition of fluid properties. Inlet: mass flow inlet.  Specification of appropriate boundary conditions at cells which coincides with or touch the domain boundary. Outlet: pressure outlet. The solution to a flow problem (velocity, pressure, temperature etc.) No-slip impermeable wall: Wall boundary conditions are used to is defined at nodes inside each cell. The accuracy of a CFD solution bound fluid and solid regions. In viscous flows, the no-slip boundary is governed by the number of cells in the grid. In general, larger the condition is enforced at walls by default, but you can specify a tangential velocity component in terms of the translational or rotational motion of number of cells betters the solution accuracy. Both the accuracy of the wall boundary, or model a "slip'' wall by specifying shear. a solution and its cost in terms of necessary computer hardware and calculation time are dependent on the fineness of the grid. Optimal (You can also model a slip wall with zero shears using the symmetry meshes are often nonuniform finer in areas where large variations occur boundary type, but using a symmetry boundary will apply symmetry from point to point and coarser in regions with relatively little changes. conditions for all equations. At present it is still up to the skills of the CFD user to design a grid that Solver: There are three distinct streams of numerical solution is a suitable compromise between desired accuracy and solution cost. techniques: finite difference, finite element and spectral methods. In Over 70% of the time spent in industry on a CFD project is devoted to outline the numerical methods that form the basis of the solver perform the definition of the domain geometry and grid generation. the following steps: Fluid Mech Open Acc Volume 3 • Issue 1 • 1000129 ISSN: FMOA, an open access journal