Attachment J.1 Solicitation 1 of 80 28 APRIL 2009 PURCHASE DESCRIPTION BODY ARMOR, MULTIPLE THREAT PLATE CARRIER 1. SCOPE 1.1 Description. This purchase description provides for a multiple threat body armor system consisting of a base vest and modular components for tailoring protection levels to defeat multiple ballistic hazards across the battlefield continuum and manage armor weight. The PLATE CARRIER is a critical safety item. This specification delineates system, subsystem, component, and subcomponent level performance requirements to accomplish the end item body armor performance (see paragraph 6.1). Body armor, multiple threat is functionally integrated with Modular Lightweight Load Equipment (MOLLE). 1.2 Classification. PLATE CARRIER components; base vest, cummerbund, side plate pockets, and small arms protective inserts (SAPI, ISAPI, ESAPI, XSAPI, Side-ESAPI). The PLATE CARRIER shall be of a single type in two classes; Type 1 – Solid Coyote 498, Type 2 – Universal Camouflage. The PLATE CARRIER will be issued separately as three subsystems, as follows. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be used in improving this document should be addressed to: John Kirejczyk, (508) 233-4348, DSN 256-4348, [email protected], US Army Natick Soldier RDEC Kansas Street, Natick, MA 01760 Attachment J.1 Solicitation 2 of 80 A) The PLATE CARRIER subsystem; consisting of the base vest assembly, cummerbund assembly, and two side plate pockets. COMPONENT SIZES Base Vest Assembly 5 sizes; X-Small, Small, medium, Large, X-Large Cummerbund Assembly 3 sizes; X-Small-Small, Medium, Large-X-Large Side Plate Pockets One size; one set B) The SAPI subsystem; consisting of a set of SAPI, ISAPI, ESAPI and XSAPI in the same size as the PLATE CARRIER. COMPONENT SIZES Small Arms Protective Insert 5 sizes: X-Small, Small, Medium, Large, X-Large (SAPI, ISAPI, ESAPI, XSAPI) C) The Enhanced Side Small Arms Protective Insert (E-SSAPI) or Enhance Side Ballistic Insert (ESBI) subsystem; consisting of a set of E-SSAPI or ESBI in one standard size or a set of X-Small ESAPI. COMPONENT SIZES Enhanced Side SAPI One size (E-SSAPI) Enhanced Side Ballistic Insert One size (ESBI) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this performance requirement. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the Solicitation (see paragraph 6.2). SPECIFICATIONS DEPARTMENT OF DEFENSE MIL-DTL-32075 - Label: For Clothing, Equipage, and Tentage (General Use). MIL-PRF-5038 - Tape, Textile and Webbing, Textile, Reinforcing Nylon Attachment J.1 Solicitation 3 of 80 MIL-PRF-63460 - Lubricant, Cleaner and Preservative for Weapons and Weapons Systems (Metric) CO/PD 00-03 - Small Arms Protective Inserts (SAPI) CO/PD 05-02 - Improved, Small Arms Protective Inserts (ISAPI) CO/PD 04-19 - Enhanced, Small Arms Protective Inserts (ESAPI) FQ/PD 07-03 - X Small Arms Protective Inserts (XSAPI) CO/PD 06-20 - Enhanced Side Ballistic Insert (ESBI) A-A-55301 - Webbing, Textile Textured or Multi-Filament A-A-55126 - Fastener Tape, Hook and Pile, Synthetic MIL-W-4088 - Webbing, Textile Woven Nylon MIL-C-43734 - Cloth, Duck, Textured Nylon MIL-STD-662F - V50 Ballistic Test for Armor MIL-STD-3027 - Performance Requirements and Testing of Body Armor MIL-DTL-46593B - PROJECTILE, CALIBERS .22, .30, .50, AND 20 mm FRAGMENT-SIMULATING MIL-W-17337 - Webbing, Textile, Woven Nylon V-T-295 - Thread, Nylon MIL-STD-810 - Environmental Engineering Considerations and Laboratory Tests A-A-55217 - Thread, Aramid, Spun Staple V-T-285 - Thread, Polyester MIL-C-7020 - Cloth, Parachute, Nylon Rip-Stop and Twill Weave MIL-E-20652 - Eyelets, Metallic, Rolled Flange Type; and Eyelet Washer MIL-F-10884 - Fasteners, Snap MIL-W-5664 - Webbing, Textile Elastic (Unless otherwise indicated, copies of the above specifications, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094 or www.dsp.dla.mil using Assist Quick Search). 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS Project Manager – Soldier Equipment, Program Executive Office – Soldier, Fort Belvoir, VA Drawing No. 2-1-2519 Universal Camouflage Pattern 60 inches Drawing No. 2-1-2519-1 Universal Camouflage Desert Sand 500 Drawing No. 2-1-2519-2 Universal Camouflage Urban Gray 501 Drawing No. 2-1-2519-3 Universal Camouflage Foliage Green 502 MANUALS TM 10-8400-203-23 General Repair Procedures for Individual Equipment; Chapter 25, Maintenance of Interceptor Body Armor System GSA Federal Standardization Manual 2000 Attachment J.1 Solicitation 4 of 80 TEST OPERATING PROCEDURES USATECOM ITOP 4-2-805 Projectile Velocity and Time of Flight Measurements Requests for above may be addressed to Defense Technical Information Center (DTIC), 8725 John J. Kingman Road, Suite 0944, Ft. Belvoir, VA 22060-6218, (703) 767-8274, http://stinet.dtic.mil/, or [email protected] (Copies of drawings, publications, and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.3 Non-government publications. The following documents forms a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are Department of Defense adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see paragraph 6.2). AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) AATCC METHOD 8 - Colorfastness to Crocking; AATCC Crockmeter Method AATCC METHOD 15 - Colorfastness to Perspiration AATCC METHOD 16 - Colorfastness to Light AATCC METHOD 22 - Water Repellency; Spray Test AATCC METHOD 61 - Colorfastness to Laundering, Home and Commercial: Accelerated AATCC METHOD 70 - Water Repellency: Tumble Jar Dynamic Absorption Test AATCC METHOD 96 - Dimensional Changes in Commercial Laundering of Woven and Knitted Fabrics Except Wool AATCC METHOD 118 - Oil Repellency: Hydrocarbon Resistance Test AATCC METHOD 119 - Color Change Due to Flat Abrasion (Frosting): Screen Wire Method AATCC METHOD 127 - Water Resistance: Hydrostatic Pressure Test AATCC Procedure 1 - Gray Scale for Color Change AATCC Procedure 2 - Gray Scale for Staining (Applications for copies should be addressed to the American Association of Textile Chemists and Colorists, PO Box 12215, Research Triangle Park, NC 27709-2215 or www.aatcc.org). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM D-204 - Sewing Threads ASTM D-1388 - Stiffness of Fabrics ASTM D 1424 - Tearing Strength of Woven Fabrics by Falling-Pendulum Type (Elmendorf) Apparatus ASTM D-1683 - Failure in Sewn Seams of Woven Fabrics ASTM D-1693 - Standard Practice for Stitches and Seams ASTM D-1777 - Standard Method for Testing Thickness of Textile Materials ASTM D-3575 - Materials, Flexible Cellular, Made From Olefin Polymers Attachment J.1 Solicitation 5 of 80 ASTM D-3776 - Mass Per Unit Area (Weight) of Woven Fabric ASTM D-3884 - Abrasion Resistance of Textile Fabrics, (Rotary Platform, Double Head Method) ASTM D-3886 - Abrasion Resistance of Textile Fabrics, (Inflated Diaphragm) ASTM D-4485 - Standard Specification for Performance of Engine Oils ASTM D-5034 - Breaking Force and Elongation of Textile Fabrics (Grab Test) ASTM D-6193 - Standard Practice for Stitches & Seam ASTM G21-90 - Test Methods for Evaluation of Effect of Fungi on Synthetic Polymeric Materials (Applications for copies should be addressed to ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959 or www.astm.org) AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI/ASQ Z1.4-2003 - Sampling Procedures and Tables for Inspection by Attributes INTERNATIONAL ORGANIZATION FOR STANDARDIZATION (ISO) International Standard 11092: 1993 - Measurement of thermal and water vapor resistance under steady state conditions (Applications for copies should be addressed to the American National Standards Institute, 25 West 43rd Street, 4th Fl., New York, New York, 10036, Tel: (212)642-4900, Fax: (212)398- 0023, http://www.ansi.org). 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First Article Test and Lot Acceptance Test. When specified, complete Body armor, multiple threat samples, representing full production quality, shall be subjected to First Article Testing in accordance with 4.2 or Lot Acceptance Testing in accordance with 4.3. 3.2 Materials and Components. The materials and components shall conform to applicable specifications, standards, and patterns required herein. 3.2.1 Cloth Outer and Inner Shell. The cloth(s) utilized to fabricate the outer shell and inner shell shall be made from lightweight, durable, synthetic cloths meeting the characteristics outlined in Appendix A, Table I when tested as specified in 4.5 (Appendix C, Table I). Color: Type 1 – Coyote 498, Type 2 - Universal Camouflage and Foliage Green 504. 3.2.1.1 Weight of Finished Fabric: The weight of the finished outer shell fabric shall be no greater than 12.0 oz/sqyd. The weight of the finished middle and inner shell fabric shall be no greater than 8.0 oz/sqyd. Attachment J.1 Solicitation 6 of 80 3.2.1.2 Pattern Execution, Outer Shell, Universal Camouflage: Type 2 - The pattern on the printed finished cloth shall be reproducible to the standard sample in respect to design, colors and registration of the respective areas. The pattern repeat shall be 36.00 (+1.25, –2.50) inches in the warp direction. The various areas of the pattern shall be properly registered in relation to each other and shall present definite sharp demarcations with a minimum of feathering or spew. Each pattern area shall show solid coverage; skitteriness exceeding that shown on the standard sample in any of the printed areas will not be acceptable. When the standard sample is not referenced for pattern execution, a pattern drawing shall be provided and the pattern shall match Drawing 2-1-2519. 3.2.2 Cloth Ballistic Panel Cover. Ballistic panel cover should be 70 Denier 1.9 oz. Nylon Ripstop. Color: Type I - Tan 380; Type II - Foliage Green 504. 3.2.3 Webbing and Tapes. Webbings and tapes shall be heat cut smooth with no burrs or residual melt. Webbings and tapes shall conform to the following requirements. a) 1.0 inch Webbing; A-A-55301, Type III, except that the spectral reflectance requirements shall be in accordance with paragraph 3.4.6 (Appendix A, for Type 1 Table IV-A and Type 2 Table IV-B) when tested in accordance with paragraph 4.5.9. Color: Type 1 – Coyote 498, Type 2 - Universal Camouflage, Foliage Green b) 1.5 inch Webbing; A-A-55301, Type VI, except that the spectral reflectance requirements shall be in accordance with paragraph 3.4.6 (Appendix A, for Type 1 Table IV-A and Type 2 Table IV-C) when tested in accordance with paragraph 4.5.9. Producer colored, textured yarns may be used. When used, thickness shall be .039 in. (min); weight shall be .90 oz/yd (min). Color: Type 1 – Coyote 498, Type 2 - Foliage Green 504 c) 2.0 inch Webbing; MIL-W-17337, except that the spectral reflectance requirements shall be in accordance with paragraph 3.4.6 (Appendix A, for Type 1 Table IV-A and Type 2 Table IV-C) when tested in accordance with paragraph 4.5.9. Producer colored, textured yarns may be used. When used, continuous filament textured nylon yarn denier shall be 1000 warp and 500 fill; breaking strength shall be 1450 lb (min); thickness shall be .042 in. (min) to .054 in. (max); filling yarns per inch shall be 40; full warp ends shall be 160; and width binder ends shall be 38. Color: Type 1 – Coyote 498, Type 2 - Foliage Green 504. d) 3.0 inch Webbing; MIL-W-17337 Class 2, continuous filament textured nylon shall be used. Color: Type 1 – Coyote 498, Type 2 - Foliage Green 504. e) 1.0 inch Tape; MIL-PRF-5038, Type III, class 2, continuous filament textured yarns shall be used except that the spectral reflectance requirements shall be in accordance with paragraph. 3.4.6 (Appendix A, Table IV) when tested in accordance with paragraph 4.5.9. Color: Coyote 498. Type 2 – Foliage Green 504 Attachment J.1 Solicitation 7 of 80 3.2.3.1 Pattern Execution, Webbing. Type 2– The pattern of the finished Universal Camouflage pattern webbing shall reproduce the standard sample with respect to design, colors, and registration of the respective areas. The pattern of the webbing shall match the pattern on the specified drawing for the Universal Camouflage, 2-1-1516, 2-1-2240, and 2-1-2519. 3.2.3.2 Shade Execution, Webbing. Type 2 - The shade of each individual color shall match the colors outlined in the Universal Camouflage standard for the Duck Cloth, Textured Nylon, Universal Pattern, MIL-C-43734 Type III Class 3. 3.2.3.3 Matching, Webbing. Type 1 PLATE CARRIER - The color of the webbing shall match the solid Coyote 498 shade PLATE CARRIER outer shell standard sample when viewed under filtered tungsten lamp which approximates artificial daylight having a correlated color temperature of 7500+/- 200K, with illumination of 100 +/- 20 foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2300 +/- 200 K. Type 2 PLATE CARRIER - The color of the webbing shall match the Universal Camouflage PLATE CARRIER outer shell standard sample when viewed under filtered tungsten lamp which approximates artificial daylight having a correlated color temperature of 7500+/- 200K, with illumination of 100 +/- 20 foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2300 +/- 200 K. 3.2.4 Elastic. Elastic shall be heat cut smooth with no burrs or residual melt. Elastic shall conform to the following requirements. a) 1.5 inch; width – 1.5 inch ±.0625, warp – textured polyester 150/2, filler – textured polyester 150/1, rubber – natural rubber, thickness - .060-.095, stretch – 100% ±10%. Color: Type 1 - Coyote 498, Type 2 - Foliage Green 504. b) 3 inch; width – 3 inch ±.060, construction – knitted, warp – textured polyester 150/1, filler – textured polyester 750d total, rubber – natural or equivalent, rubber strands – 60, thickness - .040-.045, picks per inch – 50 ±4, stretch – 110% ±15%. Color: Black. 3.2.5 Fasteners, Hook, and Loop. Hook and loop fasteners shall conform to A-A-55126, Type II, Class 1, in 1.0”, 1.5”, 2.0”, and 4.0" widths. Color: Type 1 - Coyote 498, Type 2 - Foliage Green 504. 3.2.6 Foam. The foam (located within the front and back base vest and side plate pockets) shall be closed cell with the properties specified in Appendix A, Table II when tested as specified in ASTM D-3575. The foam shall be sandwiched between the last layer of ballistic filler and back of the cloth inner shell and two layers of foam shall be sewn into the back flap. Attachment J.1 Solicitation 8 of 80 3.2.7 Polyethylene. 0.030 ±0.005 inches thick, high density per paragraph 3.3.1.3 Item 15 and paragraph 3.3.1.10. 0.045 ±.005 inches thick, high density per paragraph 3.3.1.3 Item 16. Color: Natural. 3.2.8 Cable. 3/32 Galvanized 7x7 aircraft cable coated to 5/32 +.006/-.0 with natural nylon or 3/32 Galvanized 7x7 aircraft cable coated to .165 +/-.006 with natural nylon. Ends of cable shall have no exposed metal. 3.2.9 Cable Sleeves. 5/32 copper sleeves. 3.2.10 Thread. Thread, Nylon, Bonded, Size F (Tex 112), V-T-295, Type II, Class A. Color: Type 1 – Coyote 498, Type 2 - Foliage Green 504. 3.2.11 Buckle Side Release. 1 ½ inch SR SPLIT BAR, acetal, ITW P/N 101-3150-xxxx, or equal. Color: Type 1 – Coyote 498, Type 2 - Foliage Green 504. Spectral reflectance requirements shall be in accordance with paragraph 3.4.6 (Appendix A, Type 1 - Table IV-A, Type 2 - Table IV-E) when tested in accordance with paragraph 4.5.9. 3.2.12 Tension Lock. Trovato Ladderloc TLL 150 acetal P/N 154-0150-xxxx, or equal. Color: Type 1 – Coyote 498, Type 2 - Foliage Green 504. Spectral reflectance requirements shall be in accordance with paragraph 3.4.6 (Appendix A, Type 1 - Table IV-A, Type 2 - Table IV-E) when tested in accordance with paragraph 4.5.9. A self threading (i.e. repairable) Ladderloc shall be included in repair kits as specified in the contract. 3.2.13 Loop. 1 inch, Looploc, acetal, ITW P/N 111-0100-xxxx, or equal Color: Type 1 – Coyote 498, Type 2 - Foliage Green 504. 3.2.14 Loop. 1 ½ inch Steel or brass, Welded. ITW P/N 01041-20-2188x, or equal Color: Type 1 – Coyote 498, Type 2 - Foliage Green 504 3.2.15 Loop. 1 ½ inch, Looploc, acetal, ITW P/N 111-0150-xxxx, or equal Color: Type 1 – Coyote 498, Type 2 - Foliage Green 504 3.2.16 Grommet. Plain, brass, black oxide, NASM16491, size 0, type I, class 3 3.2.17 Washer. Plain, brass, black oxide, NASM16491, size 0, type I, class 3 3.2.18 Quick Release Handle Cover. Polyvinyl chloride tubing. OD 0.380 +/- 0.005 inches, ID 0.250 +/- 0.005 inches Color. Type 1 - Tan 499, Type 2 – Foliage Green 504. 3.2.19 Cord. Dacron cord poly-braided FED SPEC.#T-C-2754-I Dacron ¼”, Tensile strength 250 lbs. 3.3 Design. The Body armor, multiple threat model dismounted system is a modular vest protecting the upper torso from multiple ballistic threats which is easily configured to defeat predicted mission threat at a minimum system weight. The PLATE CARRIER subsystem (see Attachment J.1 Solicitation 9 of 80 3.5) consists of (1) One base vest assembly made up of a outer shell base vest carrier with non- removable ballistic insert set (back and front) and one set of shoulder straps, (2) One cummerbund assembly made up of two interchangeable sides, two interchangeable cummerbund adapters and one emergency release cable (3) One set of side plate pockets with non-removable ballistic insert. Components/assembly all interface with the PLATE CARRIER. The PLATE CARRIER provides protection from conventional fragmenting munitions and multiple hits from 9mm handgun rounds. The SAPI, ISAPI, ESAPI or XSAPI subsystem consists of a set of interchangeable, sized, and contoured plates inserted into front and back pockets inside the PLATE CARRIER to provide vital organs protection against multi-hits of small arms rifle bullets and indirect fire flechettes. The Enhanced Side SAPI and Enhanced Side Ballistic Insert subsystem consists of a set of interchangeable, contoured plates inserted into the side plate pockets worn inside the cummerbund. Webbing hanger attachments on the front of the PLATE CARRIER outershell accommodate limited load carrying compatible with MOLLE modular load bearing vest pockets. The variants of Body armor, multiple threat modular system configurations follow below. Recommended enhancements are encouraged to improve its operational effectiveness and manufacturability. a) PLATE CARRIER base vest only; which does not include any of the cummerbund assembly or SAPI, ISAPI, ESAPI or XSAPI modular components. b) PLATE CARRIER base vest with cummerbund assembly with or without side plate pouches and/or one or two SAPI, ISAPI, ESAPI, or XSAPI and/or two Enhanced Side SAPI or Enhanced Side Ballistic Inserts. 3.3.1 Patterns. The Government shall furnish patterns for the baseline design from which the contractor can use applicable parts to create cutting working patterns. Compliance with patterns is required to meet interface requirements with fielded personnel combat equipment. The working patterns shall include the size, directional lines, placement marks, notches, and provided seam allowances. Baseline patterns require a 3/8” seam allowance +/-1/16” unless otherwise stated on patterns. Except for the ballistic panels, all the components of the vest shall be cut with a tolerance of +/- 1/16” in accordance with the pattern parts indicated except where changes or enhancement(s) to baseline are proposed. The ballistic panels shall be cut with a tolerance of - 1/16”/+1/8” to ensure maximum protective area of coverage is achieved (see paragraph 3.5, Appendix A, Table V-A). Drill holes are not permitted. 3.3.1.1 Base PLATE CARRIER and Components Carrier Outer Shell Item Nomenclature Computer Nomenclature Cut 1 FRONT OUTER SHELL PLATE-FRONT OUT SHLL 1 2 FRONT OUTER UPPER SHELL PLATE-FRT OUT UP SHL 1 3 FRONT LOWER FLAP PLATE-FRONT LOW FLAP 1 4 BACK OUTER SHELL PLATE-BACK OUTR SHLL 1 5 BACK UPPER FLAP PLATE-BACK UPPR FLAP 1 6 BACK LOWER FLAP PLATE-BACK LOWR FLAP 1 7 BACK SHOULDER HOLDER PLATE-BACK SHLDR HLD 2 3.3.1.2 Base PLATE CARRIER and Components Carrier Inner Shell, Attachment J.1 Solicitation 10 of 80 Item Nomenclature Computer Nomenclature Cut 8 FRONT INNER SHELL PLATE-FRONT INN SHLL 1 9 FRONT MIDDLE SHELL PLATE-FRNT MID SHLL 1 10 BACK INNER SHELL PLATE-BACK INN SHLL 1 11 BACK MIDDLE SHELL PLATE-BACK MID SHELL 1 12 PLATE SLEEVE PLATE-PLATE SLEEVE 2 13 LOOP NAME TAPE REINFORCEMENT PLATE-NAME TAPE RNFC 1 14 BACK TUNNEL FACING PLATE-TUNNEL FACING 4 3.3.1.3 Base PLATE CARRIER and Components Plastic. Item Nomenclature Computer Nomenclature Cut 15 FRONT FLAP PLASTIC PLATE-FRT PLSTC FLAP 1 16 SHOULDER STRAP PLASTIC PLATE-SHL STRP PLSTC 1 3.3.1.4 Base PLATE CARRIER and Components Ballistics. Item Nomenclature Computer Nomenclature Cut 17 FRONT BALLISTIC WIDE PLATE-FRT BLLST WIDE x 18 FRONT BALLISTIC NARROW PLATE-FRT BLLST NRRW x 19 BACK BALLISTIC WIDE PLATE-BACK BLST WIDE x 20 BACK BALLISTIC NARROW PLATE-BACK BLST NRRW x 3.3.1.5 Base PLATE CARRIER and Components Foam. Item Nomenclature Computer Nomenclature Cut 21 FRONT FOAM PLATE-FRONT FOAM 1 22 BACK FLAP FOAM PLATE-BACK FLAP FOAM 2 23 BACK FOAM PLATE-BACK FOAM 1 3.3.1.6 Base PLATE CARRIER and Components 3” Webbing Item Nomenclature Computer Nomenclature Cut 24 PLATE STRAP PLATE-PLATE INN STRP 1 3.3.1.7 Base PLATE CARRIER and Components 1.5” Webbing Item Nomenclature Computer Nomenclature Cut 25 SHOULDER STRAP BUCKLE PLATE-SHOULDER STRAP 2 26 SHOULDER STRAP YIBYAB PLATE-SHLD STRP YBYB 1 27 SIDE FEMALE BUCKLE PLATE-SID FEML BUCKL 2 28 FRONT SHOULDR BUCKLE PLATE-FRT SHLD BUCKL 2 29 BACK WAIST CENTER PLATE-BACK WST CNTR 1 30 BACK WAIST SIDE PLATE-BACK WST SIDE 2 31 BACK SHOULDER BUCKLE PLATE-BACK SHLD BCKL 2 3.3.1.8 Base PLATE CARRIER and Components 1” Webbing Item Nomenclature Computer Nomenclature Cut 32 YIBYAB TEMPLATE PLATE-YIBYAB TEMPLAT 1